1. Manuals
  2. Brands
  3. HES Manuals
  4. Industrial Equipment
  5. HS0753
  6. User manual

HES HS0753 User Manual

Hot melt applicator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS0753 and is the answer not in the manual?

Questions and answers

Related Manuals for HES HS0753

Summary of Contents for HES HS0753

  • Page 2: Table Of Contents

    1.0 Introduction ......HS0753-1-01 1.1 Safety During Installation ....HS0753-1-01 1.2 Safety During Operation ....HS0753-1-02 1.3 Safety During The Maintenance ....HS0753-1-02 1.4 Safety When Using Adhesive And Solvents ..HS0753-1-03 CHAPTER 2 EQUIPMENT FAMILARIZATION 2.0 Introduction ......HS0753-2-01 2.1 Description Of The Machine Character ..HS0753-2-02 2.2 Specification Summary ....HS0753-2-05...
  • Page 3 CHAPTER 5 TROUBLESHOOTING 5.0 Introduction ......HS0753-5-01 5.1 Safety Precautions ......HS0753-5-01 5.2 Troubleshooting Of Mechanical And Electrical Parts ......HS0753-5-01 CHAPTER 6 THE PARTS FIGURE COLLECTION 6.0 Introduction ......HS0753-6-01...

  • Page 4: Chapter 1 Safety Summary

    SAFETY SUMMARY 1.0 Introduction This chapter, intended as an introduction to the installation, operation and maintenance of HS0753 Pressure-Keeping Type Hot Melt Applicator, sets out the safety rules to be observed for preventing risk both to personnel and to the equipment.

  • Page 5: Safety During Operation

    4. Employ only qualified personnel for maintenance work on the equipment. 5. Never touch bared connection or components without discon- necting the electrical power supply while power is on. Dan- gerous voltage exise at several point in the equipment. HS0753-1-02 930906...

  • Page 6: Safety When Using Adhesive And Solvents

    1. Do not use a open flame or uncontrolled heating device to heat solvents. 2. Do not use paint-type solvents under any circumstances. These solvents are volatile and may be a fire and/or toxic- vapor hazard even at room temperature. HS0753-1-03 930906...
  • Page 7 * Cover the affected area with a clean, wet compress. * In case of severe burns, look for signs of shocks. If shock is suspected, have patint lie down, use blankets to preser- ver body heat and elevate the feet several inches. * Call a physician immediately. HS0753-1-04 930906...

  • Page 8: Chapter 2 Equipment Familarization

    EQUIPMENT FAMILARIZATION Figure 2.1 HS0753 Hot Melt Applicator 2.0 Introduction This chapter provides general information on HS0753 Pressure Keeping Type Hot Melt Applicator, also with the letout diagram (figure 2.1), equipment dimension (figure 2.2) and diagram of hydraulic system (figure 2.3), to provides the user for equipment installation.

  • Page 9: Description Of The Machine Character

    Figure 2.2 Equipment Dimension 2.1 Description Of The Machine Character The HS0753 Hot Melt Applicator is designed to melt any type or shape of adhesive with viscosity ranging from 500 to 20000 cps suitable for manual operation. This equipment has two main system, electrical control system and heating system including hydraulic system and pneumatic system.
  • Page 10 6. Glue melt fast. 7. Glue flow volume can be exactly controlled by electrical timer. 8. Pressure-keeping system with accurate construction of need- le valve nozzle reacts quite sensitively. 9. Not suitable for automatically machine system. Equipment Dimension (High Type) HS0753-2-03 930906...
  • Page 11 Figure 2.3 Hydraulic System Diagram HS0753-2-04 930906...

  • Page 12: Specification Summary

    2.3 Functional Description Of Standard 2.3.1 Power System The power system of the HS0753 Hot Melt Applicator is pneuma- tic compress air system. (Refer figure 2.3) The compress air into the tank, to pressed molten material and outlet from no- zzle.

  • Page 13: Electrical Power System

    2.3.3 Electrical Power System 1. Heating system The tank of the HS0753 is electrical heating system. The heat- er is cover surface of the tank, use a (RTD) temperature sen- sor to detect the temperature, then transfer the single to the temperature controller.

  • Page 14: Chapter 3 Operation Instructions

    CHAPTER 3 OPERATION INSTRUCTIONS 3.0 Introduction In this introduction, it contains the preparing the HS0753 Hot Melt Applicator for operation, loading it with adhesive, changing the adhesive used in it, and operating it on a daily basis. 3.1 Safety Precaution 1.

  • Page 15: The Function Of Control Panel

    3.2 The Function Of Control Panel HS0753-3-02 930906...
  • Page 16 Put this switch on "MANU" posi- tion, then the then the hot melt adhesive uotlet is controled by foot switch. Put the switch on "AUTO" position, then the hot melt adhesive outlet is control- ed by outlet timer. HS0753-3-03 930906...
  • Page 17 In this fuse base with in a 10A fuse in order to avoid the over- load or current shirt, to cause the damage of the equipment. 8. Foot Switch Plug This foot switch plug is for ex- nal foot switch to send a outlet single. HS0753-3-04 930906...

  • Page 18: Daily Operation

    3. Check the compress air set- ting. 4. Check the tank level and add adhesive material as neces- sary. CAUTION: Do not load over 4/5 of the ank capacity. 5. Select the operation form whether "MANU" or "AUTO" mode. HS0753-03-05 930906...

  • Page 19: Shut-Off Procedure

    CAUTION: Reload the adhesive material during the operation, must discharge the pressure-keeping switch, for open lid easily and safety. 3.3.2 Shut-Off Procedure 1. Put the "Pressure-Keeping" switch on discharge position. HS0753-3-06 930906...
  • Page 20 2. Turn off the main power switch. HS0753-3-07 930906...

  • Page 21: Chapter 4 Disassembly And Repair

    4.0 Introduction In this chapter contains instructions for repaying or replac- ing various parts of the HS0753 HOT MELT APPLICATOR. It de- scribe how to redisassemble the system. Some of the system de- vice, if not nesscenary, do not disassemble by operator, rec- ommend leave the devices to the qualified personnel.
  • Page 22 6. Restore the nozzle and block back to the main body care- fully, do not scratch the surface of the o-ring. 7. Tighten the socket head scews properly with L-type reang (4 mm ). HS0753-4-02 930906...

  • Page 23: Disassemble And Repair Of Quick Relieve Valve

    1. Disconnect the air source. 2. Disassemble the aluminum lid with a ψ4 stick and check the if its damage. 3. Use a (-) type sew driver to take off the muffler(6) to ch- eck if its blocked or damage. HS0753-4-03 930906...
  • Page 24 5.0 Introduction In this chapter it prevent the troubleshooting procedures for HS0753 Pressure Type Hot Melt Applicator. Some obviously prob- lem for example as damage of wire shield is general problem not including in this chapter. These general problem should be resolved in regular routine equipment maintenance.
  • Page 25 3. The quick relieve valve 3. Clean the valve or re- is blocked. place a new cap. 4. The solenoid valve is bro- 4. Replace a new one. ken. 5. Quick exhaust valve clogg- 5. Clean valve and replace new valve cap. HS0753-5-02 930906...
  • Page 26 CHAPTER 6 THE PARTS FIGURE COLLECTION 6.0 Introduction In this chapter prevent the detail drawing of HS0753 all parts assembly and electrical diagram, also with the parts item and names, for user can easily identify all difference parts. According these item number to replace the damage parts.
  • Page 27 HS0753-6-02 930906...
  • Page 28 DISPENSING VALVE 0751EE 0753T03 BLOCK CTL602 CONNECTOR HET1V-1 / HET2V-1 HEATING RING JAW09 REGULATOR K01DL MUFFLER OP9V O-RING CONNECTOR(90°) PUL602 QQ01-1 FOR QQ01 QQ01-2 FOR QQ01 QQ01-3 FOR QQ01 QQ01-4 FOR QQ01 TD0102A0 CONNECTOR TW02A0 CONNECTOR COPPER TUBE UCB1/4@ HS0753-6-03 930906...
  • Page 29 件 號 零 件 編 號 名 稱 數 量 TEMP.SWITCH H1VR LAMP EP01R POWER SWITCH D07AO PLUG FA16 FUSE BASE H3M5S2 SELECT SWITCH TM2VM6 TIMER EV1A1B SELECT SWITCH HS0753-6-04 930906...
  • Page 30 0751EE-A NOZZLE HS0753-6-05 930906...
  • Page 31 1103E14 WASHER 1103E13 SEAL 1103E21 SEAL 1103E22 SEAL 1103E23 SEAL C10B C-TYPE SNAP OP3V O-RING OP6V O-RING OP9V O-RING OP12V O-RING OP16V O-RING U05Z SC051673B SCREW SC043073B SCREW W0512Z SPRING WASHER W0412Z SPRING WASHER 1102E02-1U SHAFT 1102E02-2U SC1614 HS0753-6-06 930906...
  • Page 32 HS0753-6-07 930906...
  • Page 33 名 稱 數 量 TERMINAL BASE D07BI PLUG CTE6 CONNECTOR EP01R POWER SWITCH FA16 FUSE BASE H1VR LAMP TEMP. SWITCH N1V3MIN SOLENOID VALVE N2V3MIN SOLENOID VALVE CONNECTOR PUL601 HYDRULIC TD0102AO CONNECTOR TW02AO QUICK CONNECTOR JAW09 REGULATOR CTL602 CONNECTOR HS0753-6-08 930906...

Table of Contents