Altinex MULTI-TASKER MT103-127 User Manual
  1. Manuals
  2. Brands
  3. Altinex Manuals
  4. Recording Equipment
  5. MULTI-TASKER MT103-127
  6. User manual

Altinex MULTI-TASKER MT103-127 User Manual

Vga to 5 bnc line driver/interface and vga to 3 bnc line driver/interface/buffered loop cards for multi-tasker
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MULTI-TASKER™
MT103-127
MT103-128
MANUAL PART NUMBER: 400-0390-002
MT103-127/128
VGA TO 5 BNC LINE DRIVER/INTERFACE
AND
VGA TO 3 BNC LINE
DRIVER/INTERFACE/BUFFERED LOOP
CARDS FOR MULTI-TASKER USER'S GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MULTI-TASKER MT103-127 and is the answer not in the manual?

Questions and answers

Related Manuals for Altinex MULTI-TASKER MT103-127

Summary of Contents for Altinex MULTI-TASKER MT103-127

  • Page 1 MULTI-TASKER™ MT103-127 MT103-128 MANUAL PART NUMBER: 400-0390-002 MT103-127/128 VGA TO 5 BNC LINE DRIVER/INTERFACE VGA TO 3 BNC LINE DRIVER/INTERFACE/BUFFERED LOOP CARDS FOR MULTI-TASKER USER’S GUIDE...

  • Page 2: Table Of Contents

    OPERATION............10 RS-232 CONTROL.......... 10 DESCRIPTION OF COMMANDS ....10 SUMMARY OF COMMANDS......15 MENU MODE ..........16 TROUBLESHOOTING GUIDE......18 NO DISPLAY ........... 18 ALTINEX POLICY..........19 LIMITED WARRANTY/RETURN POLICY ..19 CONTACT INFORMATION......19...

  • Page 3: Precautions / Safety Warnings

    MULTI-TASKER™...

  • Page 4: About Your Mt103-127/128

    MULTI-TASKER™...

  • Page 5: Product Description

    MULTI-TASKER™ PRODUCT DESCRIPTION DESCRIPTION 2: MT103-128 DESCRIPTION 1: MT103-127...

  • Page 6: Application Diagram

    MULTI-TASKER™ APPLICATION DIAGRAM DIAGRAM 1: MT103-127 TYPICAL SETUP DIAGRAM 2: MT103-128 TYPICAL SETUP...

  • Page 7: Diagram 3: Mt103-127 Internal View

    MULTI-TASKER™ DIAGRAM 3: MT103-127 INTERNAL VIEW...

  • Page 8: Diagram 4: Mt103-128 Internal View

    MULTI-TASKER™ DIAGRAM 4: MT103-128 INTERNAL VIEW...

  • Page 9: Diagram 5: Mt103-127 Settings

    MULTI-TASKER™ DIAGRAM 5: MT103-127 SETTINGS MT103-127 SWITCH LOCATIONS AND SETTINGS DEFAULTS: Horizontal Position = Hardware Control Equalization = Hardware Control Composite Sync = OFF (Closed) Sync Delay = ON Sync On Green = OFF...

  • Page 10: Diagram 6: Mt103-128 Settings

    MULTI-TASKER™ DIAGRAM 6: MT103-128 SETTINGS MT103-128 SWITCH LOCATIONS AND SETTINGS DEFAULTS: Horizontal Position = Hardware Control Equalization = Hardware Control Sync Delay = ON...

  • Page 11: Installing Your Mt103-127/128

    MULTI-TASKER™ INSTALLING YOUR MT103-127/128 OPERATION Step 1. Determine the switch settings before 7.1 RS-232 CONTROL installing the MT103-127/128. The switch When used in the Multi-Tasker™ Enclosure, the settings determine the following: MT103-127/128 has many advanced remote MT103-127 and MT103-128 control capabilities, which are accessible through Equalization: Set for hardware or standard RS-232 communication.
  • Page 12 MULTI-TASKER™ The Card ID is an assigned value. It is equal to 2. [C] the enclosure slot number in which the card is This command displays the card status. installed. The value can range from 1 to 4 up to Command Format: [CnUi] 1 to 20 depending on the enclosure.
  • Page 13 MULTI-TASKER™ Example: Feedback Prefix Definitions: +MT = Multi-Tasker Card Send the command [CLRC4] to restore the card +VR = Firmware Version in slot #4 to its factory defaults. Send the +ON = ON/OFF Status command [C4] after the [CLR] command the +EQ = Equalization Setting receive the following feedback: = Signal Present...
  • Page 14 MULTI-TASKER™ SET AN ABSOLUTE VALUE 10. [SIG] Command Format: [EQ=mCnUi] The Signal Present command tests for the presence of an input signal. The card returns = EQ Value (m = # from 0 to 50) either a "1" or a "0" as feedback. Cn = Card ID (n = slot # from 1 to max slots) 1 = Signal detected Ui = Unit ID (i = # from 0 to 9)
  • Page 15 MULTI-TASKER™ In Multi-Tasker™ systems with audio and video 13. [ + ] and [ – ] cards, boards are typically grouped as follows: These commands are used to adjust the Group 1 = Video Cards Equalization and Horizontal Position and may Group 2 = Audio Cards used from...

  • Page 16: Summary Of Commands

    MULTI-TASKER™ 17. [RD] 7.3 SUMMARY OF COMMANDS This command displays the members in each Card Commands group. [VER] Receives software version Command Format: [RDGkUi] Receives status of the card Gk = Group ID (k = # from 1-8) [CnS] Saves card settings Ui = Unit ID (i = # from 0-9) [CLR] Reset card to default values...

  • Page 17: Menu Mode

    MULTI-TASKER™ 7.4 MENU MODE 7.4.2 USING MENU MODE MENU MODE commands are RS-232 commands SUGGESTION: Before using the menu mode, it that allow virtually the same functionality as is best to disable the automatic feedback programming commands. Unlike the programming feature.
  • Page 18 MULTI-TASKER™ Read each menu carefully, and continue MT103-127/128 MAIN MENU selecting keys as prompted for further PRESS KEY TO SELECT functions. (Example prompt: "Key= ") 1: CONTROL 7.4.3 MENU TYPES 2: SETUP MAIN MENU 3: STATUS The first menu displayed after selecting the 4: HELP card is the Main Menu.

  • Page 19: Troubleshooting Guide

    Solution: Make sure that the display is Starting from the Main Menu, follow the powered. If there is still no display, keystrokes below. call ALTINEX at (714) 990-2300. Select SETUP menu Select SET EQUALIZATION Increment by 1 Feedback returns EQ=21...

  • Page 20: Altinex Policy

    MULTI-TASKER™ ALTINEX POLICY 9.1 LIMITED WARRANTY/RETURN POLICY Please Altinex website www.altinex.com for details on warranty and return policy. 9.2 CONTACT INFORMATION ALTINEX, INC 592 Apollo Street Brea, CA 92821 USA TEL: 714 990-2300 TOLL FREE: 1-800-ALTINEX WEB: www.altinex.com E-MAIL: solutions@altinex.com...

This manual is also suitable for:

Multi-tasker mt103-128

Table of Contents