Safety - HABCO SE18 Installation And Instruction Manual

SAFETY - IMPORTANT!
SERVICE AND MAINTENANCE MUST BE PERFORMED BY TRAINED PROFESSIONAL
WARNING
RISK OF DEATH, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR OTHER PERSONAL INJURY!
• PLUG INTO A DEDICATED, 3 PRONG GROUNDED ELECTRICAL RECEPTACLE AND DO NOT USE EXTENSION CORDS, POWER BARS, AND/OR ADAPTERS TO
POWER THIS APPLIANCE. IF IN DOUBT, EMPLOY A CERTIFIED ELECTRICIAN TO CONFIRM YOUR POWER SUPPLY MEETS CRITERIA.
• DO NOT ALTER, IMPACT OR PLACE PRESSURE ON POWER CORD. ALLOW ADEQUATE SPACE FOR POWER CORD TO FLOAT FREELY BETWEEN CABINET AND
WALL AND DO NOT STRAIN AND/OR STRETCH POWER CORD TO REACH ELECTRICAL RECEPTACLE.
• INSPECT POWER CORD FOR ANY DAMAGE PRIOR TO POWERING AND WHENEVER HABCO® CASSETTE® IS EXCHANGED OR APPLIANCE IS MOVED. DO
NOT PLUG THIS APPLIANCE INTO WALL RECEPTACLE IF POWER CORD IS DAMAGED.
• DO NOT ACCESS MECHANICALLY FASTENED AREAS WITHOUT PERMISSION OF OWNER AND READING AND UNDERSTANDING PRODUCT MANUAL.
• DISCONNECT POWER BEFORE ACCESSING MECHANICALLY FASTENED AREAS.
• DO NOT INSTALL OUTDOORS, IN DIRECT SUN, DAMP, EXTREME HEAT AND/OR COLD CONDITIONS.
• DO NOT INSTALL APPLIANCE WHERE STORAGE, HANDLING AND/OR DISPENSING FLAMMABLE AND/OR EXPLOSIVE MATERIALS OCCUR.
• WHEN STORING APPLIANCE, BLOCK DOOR SLIGHTLY AJAR, BUT SECURE TO AVOID ACCIDENTAL ENTRAPMENT.
• WHEN DISPOSING OF APPLIANCE, REMOVE DOORS TO AVOID ACCIDENTAL ENTRAPMENT AND POTENTIAL OF SUFFOCATION.
• KEEP PLASTIC PACKAGING MATERIAL AWAY FROM CHILDREN AND ANIMALS, AND DISPOSE SAFE AND SECURE.
WARNING
POTENTIAL RISK OF PERSONAL INJURY!
• EMPLOY BEST HEALTH AND SAFETY LIFTING PRACTICES WHEN REMOVING SHIPPING PLATFORM(S); LEVELING CABINET; MOVING OR LIFTING CAS-
SETTE®; MOVING OR LIFTING DOORS; AND MOVING APPLIANCE. IF IN DOUBT, ASK FOR HELP.
• EMPLOY BEST HEALTH AND SAFETY PERSONAL PROTECTION PRACTICES AND ADHERE TO MANUFACTURER'S WARNINGS WHEN USING TOOLS AND
CLEANING AGENTS.
• DO NOT CLIMB AND/OR HANG ON CABINET, SHELVING AND/OR DOORS.
• USE CARE WHEN HANDLING OR CLEANING METAL PARTS.
• HOLD DOOR AGAINST CABINET WHILE REMOVING BRACKET AND FASTENERS. MAGNETIC DOOR GASKET WILL ASSIST. REMOVAL OF THE SET-SCREW
WILL LEAVE DOOR UNSECURED.
NOTICE
ESSENTIAL INFORMATION, OR THAT WHICH MAY CAUSE APPLIANCE DAMAGE OR ENVIRONMENTAL HARM!
• DO NOT LOCATE APPLIANCE IN DIRECT SUNLIGHT OR IN CLOSE PROXIMITY TO HIGH HEAT SUCH AS FRYERS, RANGES, AND/OR HEATING DUCTS.
• USE ONLY MILD ANTI-BACTERIAL, NON-ABRASIVE 'DISH SOAP' DETERGENT, AND SOFT CLOTH (OR BRISTLE BRUSHES WHERE SPECIFIED) FOR CLEANING
YOUR APPLIANCE. FOR STUBBORN RESIDUE, SUCH AS GREASE BUILD-UP ON CONDENSER (HEAT-EXCHANGE) COIL, EMPLOY THE SERVICES OF A QUALI-
FIED PROFESSIONAL.
• CABINET MUST BE LEVELED FRONT TO BACK AND SIDE TO SIDE TO ENSURE OPTIMUM PERFORMANCE AND UTILITY.
• MAINTAIN A CLEAN CONDENSER COIL (BOX-SHAPED COMPONENT LOCATED BEHIND THE LOWER GRILL) TO PREVENT DAMAGE TO REFRIGERATION
PARTS AND POOR PERFORMANCE NOT COVERED UNDER WARRANTY. QUALIFIED PROFESSIONAL TO DISCONNECT POWER BEFORE ACCESSING ME-
CHANICALLY FASTENED AREAS.
• DO NOT OVERLOAD CABINET WITH PRODUCT AND/OR LOAD PRODUCT HIGHER THAN THE LOAD LEVEL LINE, LOCATED ON LEFT HAND INTERIOR WALL.
DO NOT OBSTRUCT AIR-RETURN GRILLS LOCATED INSIDE CABINET NEAR THE LOWER LEFT AND RIGHT OF THE REAR AIR DISTRIBUTION PANEL. DO
NOT OBSTRUCT EXTERIOR, LOWER FRONT GRILL. FAILURE TO COMPLY WILL RESULT IN RESTRICTED AIR CIRCULATION, SUBSTANTIALLY REDUCED COOLING
PERFORMANCE, FROZEN PRODUCT AND VOID WARRANTY. FAILURE TO COMPLY MAY RESULT IN RESTRICTED AIR CIRCULATION, SUBSTANTIALLY REDUCED
COOLING PERFORMANCE AND DAMAGE TO REFRIGERATION COMPONENTS.
• THERMOSTAT SETTING CHANGES MAY INCREASE REFRIGERATION TO FREEZING CONDITIONS. FREEZING CONDITIONS CAN DAMAGE REFRIGERATION
SYSTEM AND COMPONENTS, AND MAY CAUSE PRODUCT LOSS. ISSUES ARISING FROM ADJUSTMENTS OR CORRECTIONS DUE TO ADJUSTMENTS OF THE
THERMOSTAT FACTORY PRESET TEMPERATURE IS NOT COVERED UNDER WARRANTY.
• DO NOT PUSH, LEAN-ON OR FORCE STAINLESS STEEL TUBE EXTENDING FROM CABINET IN THE CASSETTE® REFRIGERATION CHAMBER. DO NOT FORCE
REFRIGERATION CASSETTE® WHEN REINSTALLING. SLIDE INTO PLACE GENTLY AND EVENLY, APPLYING EQUAL PRESSURE TO EACH SIDE OF CASSETTE®.
• ENSURE THAT APPLIANCE, REFRIGERANT AND/OR COMPONENTS ARE DISPOSED OF IN A MANNER IN KEEPING WITH LOCAL AND FEDERAL REGULA-
TIONS.
• APPLIANCE MUST BE RUN FOR A PERIOD OF 24 HOURS PRIOR TO USE.
• AFTER ACCESSING REFRIGERATION OR ANY OTHER MECHANICALLY FASTENED AREAS OF THE APPLIANCE, REFASTEN SECURELY.
• DO NOT USE CORROSIVE AGENTS SUCH AS SOLVENT OR ACID TO CLEAN THE FREEZER. DO NOT USE ABRASIVE CLOTHS OR CLEANSERS.
• DO NOT STORE OUTDOORS, IN DIRECT SUN, DAMP, EXTREME HEAT AND/OR COLD CONDITIONS.
• DO NOT INSTALL DIRECTLY BENEATH UNDIFFUSED AIR CONDITIONING VENTS.
• DOOR REVERSALS COMPLETED AT FACTORY ARE WARRANTED. ANY ISSUES AND SUBSEQUENT SOLUTIONS ARISING FROM CUSTOMER REVERSED
DOORS ARE THE RESPONSIBILITY OF THE END-USER. DOOR ADJUSTMENTS ARE NOT COVERED UNDER WARRANTY. INSPECT DOOR HARDWARE FOR
WEAR WHEN REVERSING OR SERVICING.
CONSEQUENTIAL, ECONOMIC AND/OR PRODUCT LOSS OR SPOILAGE IS NOT COVERED BY THIS LIMITED COMMERCIAL WARRANTY.
FAILURE TO COMPLY WITH THE INFORMATION OUTLINED IN THIS MANUAL WILL VOID
READ AND UNDERSTAND THIS INFORMATION FIRST
HABCO® COMMERCIAL LIMITED WARRANTY.
© HABCO Manufacturing Inc. "HABCO®, Cassette®, Cold Space Merchandiser®" are registered trademarks of HABCO Manufacturing Inc. Domestic and International Patents. Page 3
HABCO® TECHNICAL DOCUMENT - C096832 • 10126169