Table of Contents
Advertisement
SAFETY - IMPORTANT!
SERVICE AND MAINTENANCE MUST BE PERFORMED BY TRAINED PROFESSIONAL
WARNING
RISK OF DEATH, FIRE, EXPLOSION, ELECTRICAL SHOCK AND/OR OTHER PERSONAL INJURY!
•
PLUG INTO A DEDICATED, 3 PRONG GROUNDED ELECTRICAL RECEPTACLE AND DO NOT USE EXTENSION CORDS, POWER BARS, AND/OR ADAPTERS TO
POWER THIS APPLIANCE. IF IN DOUBT, EMPLOY A CERTIFIED ELECTRICIAN TO CONFIRM YOUR POWER SUPPLY MEETS CRITERIA.
•
DO NOT ALTER, IMPACT OR PLACE PRESSURE ON POWER CORD. ALLOW ADEQUATE SPACE FOR POWER CORD TO FLOAT FREELY BETWEEN CABINET AND
WALL AND DO NOT STRAIN AND/OR STRETCH POWER CORD TO REACH ELECTRICAL RECEPTACLE.
•
INSPECT POWER CORD FOR ANY DAMAGE PRIOR TO POWERING AND WHENEVER HABCO® CASSETTE® IS EXCHANGED OR APPLIANCE IS MOVED. DO
NOT PLUG THIS APPLIANCE INTO WALL RECEPTACLE IF POWER CORD IS DAMAGED.
•
DO NOT ACCESS MECHANICALLY FASTENED AREAS WITHOUT PERMISSION OF OWNER AND READING AND UNDERSTANDING PRODUCT MANUAL.
•
DISCONNECT POWER BEFORE ACCESSING MECHANICALLY FASTENED AREAS.
•
DISCONNECT POWER BEFORE CHANGING LAMPS.
•
DO NOT INSTALL OUTDOORS, IN DIRECT SUN, DAMP, EXTREME HEAT AND/OR COLD CONDITIONS.
•
DO NOT INSTALL APPLIANCE WHERE STORAGE, HANDLING AND/OR DISPENSING FLAMMABLE AND/OR EXPLOSIVE MATERIALS OCCUR.
•
WHEN STORING APPLIANCE, BLOCK DOOR SLIGHTLY AJAR, BUT SECURE TO AVOID ACCIDENTAL ENTRAPMENT.
•
WHEN DISPOSING OF APPLIANCE, REMOVE DOORS TO AVOID ACCIDENTAL ENTRAPMENT AND POTENTIAL OF SUFFOCATION.
•
KEEP PLASTIC PACKAGING MATERIAL AWAY FROM CHILDREN AND ANIMALS, AND DISPOSE SAFE AND SECURE.
WARNING
POTENTIAL RISK OF PERSONAL INJURY!
•
EMPLOY BEST HEALTH AND SAFETY LIFTING PRACTICES WHEN REMOVING SHIPPING PLATFORM(S); LEVELING CABINET; REVERSING DOORS; AND MOV-
ING APPLIANCE. IF IN DOUBT, ASK FOR HELP.
•
EMPLOY BEST HEALTH AND SAFETY PERSONAL PROTECTION PRACTICES AND ADHERE TO MANUFACTURER'S WARNINGS WHEN USING TOOLS AND
CLEANING AGENTS.
•
DO NOT CLIMB AND/OR HANG ON CABINET, SHELVING AND/OR DOORS.
•
USE CARE WHEN HANDLING OR CLEANING METAL PARTS.
NOTICE
ESSENTIAL INFORMATION, OR THAT WHICH MAY CAUSE APPLIANCE DAMAGE OR ENVIRONMENTAL HARM!
•
DO NOT LOAD REFRIGERATOR ABOVE LOAD LEVEL LINE INDICATOR LOCATED ON LEFT INTERIOR WALL. DO NOT LOAD PRODUCT OUTSIDE PERIMETER OF
SHELVES. DO NOT BLOCK EXTERIOR, LOWER FRONT GRILL. FAILURE TO COMPLY MAY RESULT IN RESTRICTED AIR CIRCULATION, SUBSTANTIALLY REDUCED
COOLING PERFORMANCE, DAMAGE TO REFRIGERATION COMPONENTS, AND/OR FROZEN PRODUCT.
•
DO NOT LOCATE APPLIANCE IN DIRECT SUNLIGHT OR IN CLOSE PROXIMITY TO HIGH HEAT SUCH AS FRYERS, RANGES, AND/OR HEATING DUCTS.
•
USE ONLY MILD ANTI-BACTERIAL, NON-ABRASIVE 'DISH SOAP' DETERGENT, AND SOFT CLOTH (OR BRISTLE BRUSHES WHERE SPECIFIED) FOR CLEANING
YOUR APPLIANCE. FOR STUBBORN RESIDUE, SUCH AS GREASE BUILD-UP ON CONDENSER (HEAT-EXCHANGE) COIL, EMPLOY THE SERVICES OF A QUALI-
FIED PROFESSIONAL.
•
CABINET MUST BE LEVELED FRONT TO BACK AND SIDE TO SIDE TO ENSURE OPTIMUM PERFORMANCE AND UTILITY.
•
MAINTAIN A CLEAN CONDENSER COIL (BOX-SHAPED COMPONENT LOCATED BEHIND THE LOWER GRILL) TO PREVENT DAMAGE TO REFRIGERATION
PARTS AND POOR PERFORMANCE NOT COVERED UNDER WARRANTY. QUALIFIED PROFESSIONAL TO DISCONNECT POWER BEFORE ACCESSING ME-
CHANICALLY FASTENED AREAS.
•
DO NOT BLOCK EXTERIOR, LOWER FRONT GRILL. FAILURE TO COMPLY MAY RESULT IN RESTRICTED AIR CIRCULATION, SUBSTANTIALLY REDUCED COOL-
ING PERFORMANCE AND DAMAGE TO REFRIGERATION COMPONENTS.
•
THERMOSTAT DIAL SETTING CHANGES MAY TURN REFRIGERATION SYSTEM OFF (90º COUNTER-CLOCKWISE) OR INCREASE REFRIGERATION TO FREEZ-
ING CONDITIONS (ANY ADJUSTMENT FURTHER CLOCKWISE). FREEZING CONDITIONS CAN DAMAGE REFRIGERATION SYSTEM AND COMPONENTS, AND
MAY CAUSE PRODUCT LOSS. CHANGES TO THE THERMOSTAT DIAL SETTING SHOULD BE MADE BY A QUALIFIED PROFESSIONAL AFTER DISCONNECTING
POWER TO APPLIANCE. ISSUES ARISING FROM ALTERATIONS OF FACTORY PRESET POSITION ARE NOT COVERED UNDER WARRANTY.
•
DO NOT PUSH, LEAN-ON OR FORCE CONDENSATE DRAIN TUBE.
•
ENSURE THAT APPLIANCE, REFRIGERANT AND/OR COMPONENTS ARE DISPOSED OF IN A MANNER IN KEEPING WITH LOCAL AND FEDERAL REGULA-
TIONS.
•
APPLIANCE MUST BE RUN FOR A PERIOD OF 24 HOURS PRIOR TO USE.
•
AFTER ACCESSING REFRIGERATION OR ANY OTHER MECHANICALLY FASTENED AREAS OF THE APPLIANCE, REFASTEN SECURELY.
•
DO NOT STORE OUTDOORS, IN DIRECT SUN, DAMP, EXTREME HEAT AND/OR COLD CONDITIONS.
•
DO NOT INSTALL DIRECTLY BENEATH UNDIFFUSED AIR CONDITIONING VENTS.
•
DOOR REVERSALS COMPLETED AT FACTORY OR BY HABCO® ARE WARRANTED. ANY ISSUES AND SUBSEQUENT SOLUTIONS ARISING FROM CUSTOMER
REVERSED DOORS ARE THE RESPONSIBILITY OF THE END-USER. DOOR ADJUSTMENTS ARE NOT COVERED UNDER WARRANTY. INSPECT DOOR HARD-
WARE FOR WEAR WHEN REVERSING OR SERVICING.
CONSEQUENTIAL, ECONOMIC AND/OR PRODUCT LOSS OR SPOILAGE IS NOT COVERED BY HABCO® COMMERCIAL LIMITED WARRANTY.
FAILURE TO COMPLY WITH THE INFORMATION OUTLINED IN THIS MANUAL WILL VOID
READ AND UNDERSTAND THIS INFORMATION FIRST
HABCO® COMMERCIAL LIMITED WARRANTY.
© HABCO Manufacturing Inc. "HABCO®, Cassette®, Cold Space Merchandiser®" are registered trademarks of HABCO Manufacturing Inc. Domestic and International Patents. Page 3
HABCO® TECHNICAL DOCUMENT - C097584 • 10125169
Hide quick links:
Advertisement
Table of Contents
