BN Thermic SWD Series Instructions

Thank you for purchasing a BN Thermic product. Manufactured to a high standard, this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance. Please ensure instructions remain with your
customer for their reference.
REGISTER: PLEASE REGISTER THIS PRODUCT ONLINE TO ACTIVATE YOUR GUARANTEE AT
PLEASE READ THESE INSTRUCTIONS, NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS,
AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1 . SA FET Y IN ST RUCT ION S
1.1 ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. If in any doubt consult a qualified electrician.
You must also read and understand the following instructions concerning electrical safety.
▪
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
▪
Installation should always be carried out by a qualified electrician or a competent person in accordance with current electrical
regulation.
▪
Ensure that the insulation of all the cables on the appliance is undamaged and safe, before connecting it to the power supply.
▪
Ensure that the cables are always protected against short circuit and overload.
▪
Regularly inspect the power supply cables and plugs etc. for wear or damage and check all connections to ensure that none
are loose.
▪
Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that a correctly rated
fuse is fitted.
▪
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a
qualified electrician.
▪
The unit should be protected by a suitably rated isolator and fuse or MCB.
▪
Tubular heaters are IP66 rated.
▪
Do not attach this tubular heater to an extension cord it must be hard wired in position.
1.2 GENERAL SAFETY INSTRUCTIONS
✓
Remove all packaging and store it away from children, check the package and heater for visible damage or tampering.
✓
Familiarise yourself with the applications and limitations of the tubular heater.
✓
Ensure the tubular heater is in good order and condition both physically and electrically before use. If in any doubt, do not
use the unit and contact your supplier.
✓
Only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your
warranty.
✓
Keep tools and other items away from the tubular heater when it is in use.
✓
Keep children and unauthorised persons away from the heater, as it gets very hot. An optional grille is available.
✓
Disconnect from mains and allow to cool before attempting any cleaning or maintenance.
X DO NOT use in areas where hazardous gasses or dusts may be present.
X DO NOT locate the heater directly below the power outlet.
X DO NOT disassemble the heater for any reason. This heater must be checked by qualified personnel only.
X DO NOT use this tubular heater to
perform a task for which it has not
been designed.
❑
WARNING! Some models (U Type)
are not equipped with a built-in device
to control the room temperature. Do
not use this heater in a small room if
it is occupied by people not capable
of leaving the room on their own,
unless constant
provided.
❑
WARNING! Ensure you observe the
safety distances
heights and there is no possibility of
inflammable materials coming into
contact.
supervision is
and mounting
www. .co.uk
bnthermic
INSTRUCTIONS FOR:-
FINNED TUBULAR HEATERS
SWD SERIES