Preface: Please read through these instructions for use carefully. It contains valuable instructions on correct use of the JetCam, but also tips for effective operation. We wish you all the best when using it. Team OPTRONIC Page 3...
Warnings: · For cleaning, do not use any high- pressure cleaners · Do not place any heavy objects on the device · Do not perform repair work by yourself, consult an authorised customer service otherwise the manufacturer guaranteed shall be invalidated! ·...
Data sheet Reel with: 1/2“ connection with BSP female thread Needle valve for water regulation Reel brake with guide holes Hand crank for winding the hose Pneumatic tyres for easy transport Slide rails for easy loading and unloading Protection class IP64 Control unit with: Light control Battery display...
Page 7
Voltage: 11.1 V DC Charging voltage: 15 V DC Rechargeable Output: 5200 mAh (for approx. 4-5 operating hours) battery Charging time: min. 5 hours Possible hazards Lithium-Ion batteries are sealed gas tight and are harmless as long as they are used and handled in line with the manufacturer regulations. Warning Never use battery chargers that are not intended for the battery type! Do not short-circuit.
Page 8
Steering part (all) comprising: Lateral steering nozzle 1.2 mm M4 Length approx. 35 mm Throughput approx. 40-60 l/min at 100-150 bar Completely pre-assembled Plug-in system on the camera head side Without camera head 6 jets (6 x 1,1 mm for 3/8" or 6 x 1.2 mm for 1/2"...
Page 9
Digital video recorder, integrated Menu navigation via remote control integrated in the monitor housing The recorder generates it own folder on the SD card inserted Films / photos are saved in a separate sub-folder according to date and time 800 x 600 pix as ideal presetting, Recording of videos: possible: 1280 x 720 pix Recording of individual images:...
Preparation: Preparation Please make sure that the following are available at the operating location: high-pressure pump: · - for JetCam with 3/8" hose app. 40 - 60 litre / 100 - 150 bar at the unit - for JetCam with 1/2" hose app. 60 - 80 litre / 100 - 150 bar at the unit ·...
Preparatory measures before starting work: On the camera Make sure that the Camera head is cleaned. To ensure for a clear view as long as possible, the sapphire glass and the macrolon must be cleaned before or after being used each time. Changing the camera head When fastening the camera head, make sure that the fit on the camera head and hose piece match each other precisely !!!
Page 13
Water side · Connect the water hose of the high-pressure washer with 1/2” BSP external thread to the JetCam (two 27 mm open-ended spanners are required for this purpose) · Make sure that the needle valve is completely opened. In the top view of the controller: Close (clockwise direction of rotation) Open (counter-clockwise direction of rotation) ·...
Commissioning: · Pull out the reel trolley completely · Switch on the system with the light control (if the video recorder is fitted, you can hear a brief “beep” tone) · Set the monitor to the viewing position and also switch on (right blue button “Power“) Channel selection: Live view (“Video 2“) or view via the video channel (“Video 1“).
Page 15
Working with the JetCam: To avoid water damage or water leaking in an uncontrolled manner, the camera head along with steering part must be completely inserted into the pipe to be inspected. Before the system is supplied with pressurised water, hold the hose tight in order not to loose control over the high-pressure system! ·...
· The steering nozzle is always aligned downwards from the camera so that the top side of the camera image is decisive for the direction that should be travelled. If a branch can be seen in the camera image that should be travelled along, the camera head must be aligned by twisting on the hydraulic hose so that the branch is in the upper area (12 o'clock) of the camera image in the live video.
Maintenance, cleaning the nozzle inserts: Cleaning the nozzle (e.g. puncture) Steering nozzle: for cleaning the steering nozzle, the nozzle always has to be disassembled otherwise the reason for the blockage is guided back into the inside and creates another blockage. Nozzle: disassembly of the nozzles is also a requirement for cleaning the nozzle inserts.
Working with accessories / optional Forward jet: Assembly Remove the M6x5 threaded pin and there, screw on the front jet nozzle. Caution: The forward jet may only be tightened using an 8 mm open-ended spanner (do not tighten hand-tight). Keep the grub screw removed in a safe place. You will need it again if you want to work without the front jet nozzle.
Working with accessories / options: electronics Locating transmitter The locating transmitter 512 Hz is switchable. The location switch is located on the control box. If the locating transmitter is switched on, the image switches off. As soon as the locating switch is switched off again, the image appears again. WIFI If a JetCam is equipped with WIFI, this transmits permanently when the system is switched on.
Page 20
Recording button These buttons do not replace the remote control. (yellow): Photo (black): Pause / start video (red): Start / end film Page 21...
Main menu To display the menu, “Video 1” must be selected on the monitor. Now press the “Menu” button on the remote control. The following settings can be made here: 1. Video image resolution 2. Image frequency (images / second) 3.