Advertisement
Quick Links
Advertisement
Related Manuals for OPTRONIC jetcam 4.0
Summary of Contents for OPTRONIC jetcam 4.0
- Page 1 Operating instructions V2.0 Page 1 www.optronic.de...
- Page 2 Table of contents Preface (Page 3) Warning notices (Page 4) Quality features (Page 4) Description of components (Page 5) Data sheet (Page 6-8) Preparation (Page 10) Preparation (Page 11-12) Commissioning (Page 13) Cleaning/inspection using the JetCam (Page 14-15) Straight sections, elbows, branches, over soil Cleaning the nozzle (Page 15) V2.0 Page 2...
- Page 3 Preface Please read through these instructions for use carefully. It contains valuable instructions on correct use of the JetCam, but also tips for effective operation. We wish you all the best when using it. Team OPTRONIC V2.0 Page 3...
- Page 4 Warnings · For cleaning, do not use any high- pressure cleaners · Do not place any heavy objects on the device · Do not perform repair work by yourself, consult an authorised customer service. Otherwise, the manufacturer guarantee shall be invalidated! ·...
-
Page 5: Component Description
Component description V2.0 Page 5... - Page 6 Factsheet V2.0 Page 6...
- Page 7 V2.0 Page 7...
- Page 8 Battery voltage: 14.4 V DC Charging voltage: 17 V DC Output: 6.9 Ah (for app. 10 operating hours) Charging time: app. 7 hours Possible hazards ! Lithium-Ion batteries are sealed gas tight and are harmless as long as they are used and handled in line with the manufacturer regulations. Warning ! Never use battery chargers that are not intended for the battery type! Do not short-circuit.
- Page 9 Instructions for use The JetCam has been optimally designed for your tasks in diameters from 50 to 300 mm V2.0 Page 9...
- Page 10 Preparation Please make sure that the following are available at the operating location: · a jetter, where the output corresponds approximately to: 40 - 60 litre / min. 100 - 150 bar for JetCam with 3/8" hose 60 - 80 litre / min. 100 - 150 bar for JetCam with 1/2" hose ·...
-
Page 11: Preparatory Measures
Preparatory measures On the camera Make sure that the camera head is cleaned. To ensure for a clear view as long as possible, the sapphire glass and the macrolon must be cleaned before or after being used each time. Changing the camera head When fastening the camera head, make sure that the fit on the camera head and steering part match each other ·... - Page 12 Water side Connect the hp-hose of the jetter with 1/2” BSP external thread to · the JetCam (two 27 mm open-ended spanners are required for this purpose) Make sure that ball valve is completely opened. · · Clean steering nozzle and nozzle inserts of the nozzle. These may not be clogged.
- Page 13 Commissioning · Download and install the software (Sewerlink) for smartphone, tablet, Wifi monitor or Laptop at https://www.wincan.com/en/support/downloads/. Operating instructions for Sewerlink: https://www.wincan.com/en/support/documentation/ · Pull out the reel trolley completely · Switch the system on / off using the knob on the control box Switching-on: Press the pushbutton ~1 sec.
- Page 14 Cleaning/i with the To avoid water damage or water leaking in an uncontrolled manner, the camera head along with steering part must be completely inserted into the pipe to be inspected. Before the system is supplied with pressurised water, hold the hose tight in order not to loose control over the system! ·...
-
Page 15: Cleaning The Nozzles
Elbows If this should be a problem, the steering nozzle may be aligned in an unfavourable angle to the pipe and thus may even prevent it from being travelled over. Solution: Pull back the hose, twist and as a result, move the elbow at a different angle. Branches, T-pieces Move to the branch or T-piece in the position (by twisting the hose) in which you see the branch or T-piece in the "12 o'clock"...