Standard, deluxe and professional 40 roll laminators (21 pages)
Summary of Contents for Dry-Lam HLA-2301
Page 1
AUTO LAMITOR Instruction Manual MODEL NO : HLA-2301...
Page 2
About the warning mark The following marks are added to the explanations of things that you should never do or should be careful about in this manual and the main body. Be sure to read these marks and follow the instructions. General cautions and warnings We will inform you of general cautions and warnings that are not specified.
Page 3
Warning (about installation location) Do not install in such a place. When installing this machine, avoid the following places as it may cause safety problems such as fire, electric shock, and tipping, and may also cause a malfunction. This equipment is not suitable for use in locations where children are likely to be present. Places exposed to direct sunlight Extremely hot places Near the air conditioner outlet...
Page 4
• Avoid ties, necklaces, and hanging accessories. • Avoid loose clothing. If it gets caught, immediately turn off the power switch (○) or disconnect the power plug. • Be careful not to pull your hair in. 2. When operating this machine •...
Wipe off any dirt with a soft cloth. If it is very dirty, wipe it off with a soft cloth dampened with a small amount of water or a neutral detergent. After using a neutral detergent, be sure to wipe it off with a soft cloth soaked in water only. Attention (about the remaining amount of film) This machine has a function to notify the end of the film (film shuryo laminating error).
Page 6
Expansion tray Tray used for A3 size processing Tray A tray for feeding paper of A4 or smaller size Feeding roll (Sabaki roll) Roll that pulls in paper one by one Separating roll (Heat roll) Roll that separates paper one by one Feeder part Unit part feeds paper one by one Heating roll...
Page 7
RESET button It is used to clear the error and return the setting value to the default. UP button Used to change the set value. DOWN button Used to change the set value. Menu/Back button Moves to the setting mode. SET button Used to confirm the selection.
2-3. Other operation switches There is a switch on the slitter inside the main body where the operation pannel is installed. ① ② ① Manual transport switch Used when setting the film. 搬送 When the switch is tilted to the left, it will be transported in the forward rotation direction.
3-1. Install the machine In order to operate the machine smoothly and replace the film smoothly, secure a sufficient space (20 cm or more) around the machine and install it. ※ For the installation environment, please read the warning (about the installation location) and warning (about the power supply and ground) carefully and install correctly.
Page 10
1. Prepare the following items. ・HKK exclusive film * Please prepare the HKK exclusive film "AL-ROLL FILM" sold separately. * Because the special film is a set of two, be sure to use it as a set. • A3 size thick paper (thickness: 0.20 to 0.25 mm)… 1 sheet * At the time of purchase, it is set in this unit.
Page 11
6. Remove the slitter adjustment knob from the groove by tilting it toward you, and move it to the film set position (arrow in the picture ). Notice ◎Doing the film set at a position other than the film set position may cause a malfunction. 7.
13. Using double-sided tape, attach the upper and lower films to the thick paper. ※ When purchasing the film, double-sided tape is attached to the film. Notice ◎ Attach the upper and lower films to thick paper so that there are no wrinkles. ◎...
Page 13
A3・A4paper B4・B5 paper Move the Paper Guy (left and right) in the input tray so that the paper is in the center of the tray. (Loosen the paper guide adjustment knob before moving it.) Tighten the knob after adjustment. Push down on the edge of the feeder tray by hand. Set the paper so that it hits the back of the feeder tray (maximum load capacity: 200 sheets of copy paper).
Supplement Eco mode If the laminating process is not performed for 30 minutes or more, or if the button on the operation panel is not pressed, the eco mode is entered and the temperature is set to 60 ° C. Press any of the RESET buttons to cancel the eco mode.
Page 15
6-4. Set with / without margin (border) ... Slitter part It is used to set the margin (border) of the slitter part. Move the slitter adjustment knob to set. -How to move the slitter adjustment knob- Turn down the slitter adjustment knob to remove it from the groove. Close the slitter cover when the setting is completed. Back Front 6-5.
If necessary, adjust the position of the paper with the feed fine adjustment knob on the feeder tray. When the finished product is (A), turn the feed fine adjustment knob to the right. When the finished product is (B), turn the feed fine adjustment screw counterclockwise.
Page 17
Phenomenon Checklist Treatment Have you checked and ● Laminated paper is not · Paper curl adjusted? ejected Make sure the paper is not curled. (Hansou error) • Curl of laminated paper (Laminate error) Adjust the film tension. • Amount of trash in the trash can When trash is loaded, the trash during processing may not fall into the trash can and the trash may collect in the slitter unit, so please dispose of the trash in the trash can diligently.
Page 18
7. When in trouble Phenomenon Checklist Treatment ●Hansou error occurred Is the paper jammed between Pull out the film or laminated paper (FEEDING ERROR ) the cutter and the slitter? ●Lamination error Is the paper jammed between [1]Pull out the film or laminated paper. occurred the cutter and the laminator? [2 If there is paper in the "feeder tray", slowly pull it out toward you.
Page 19
7. When in trouble Phenomenon Checklist Treatment ● Film error occurred Is the film with IC installed Install the film with IC exactly on the bottom side. (CHECK FILM) correctly on the underside? ●Cover opened error Is the cover open? Close the "feeder cover"...
8. Machine specifications Product name HLA-2301 (model number) Maximum laminate width 320mm Maximum laminate 0.4mm(including film thickness) thickness Corresponding film 38、75、100、125mic(0.038、0.075、0.100、0.125mm) thickness Corresponding paper 0.07~0.25mm (70~250mic・64~240g/m thickness Laminating speed 0.5~1.7m/min Range of temperature 80~130℃ Warm-up time About 6mins and a half Power-supply voltage AC100~240V(50/60Hz)
Page 21
9. Stand specifications This Model HLA-2301 is for use only with HLA2301-S by Kalbas Limited. Use with other stand may result in instability causing injury.
Need help?
Do you have a question about the HLA-2301 and is the answer not in the manual?
Questions and answers