Table of Contents
Advertisement
Hot Keys
Your safe has a list of hotkeys shortcuts.
Tamper Detection: To check for tampering press and hold keys '2' and '4' together for 3 seconds. The '3' key will
glow RED to indicate tampering or GREEN to indicate no tampering. The safe considers an incorrect keypad entry
and unauthorized fingerprint scan (biometric model only) as tampering. You can reset the tamper detection by
opening the safe through one of the authorized entry points.
Toggle Sound: Toggle between four different sound settings. High pitch, medium pitch, low pitch, or off. To toggle
the setting press and hold keys '1' and '3' together for 3 seconds. If the '2' '4' and '5' keys glow GREEN the sound
is High; if the '2' and '4' keys glow GREEN the sound is Medium; if the '2' key glows GREEN the sound is Low, and
if the '2' key glows RED the sound is off. The sound is medium pitch by default.
Toggle Travel Mode: Disable the safe to save battery and prevent tampering. Travel Mode disables the proximity
sensor, fingerprint sensor, keypad, and Bluetooth features. To toggle travel mode ON/OFF press and hold keys '1'
'3' and '5' together until the safe beeps and the keys light up. If keys '2' and '4' glow RED, the safe is disabled; if
keys '2' and '4' glow GREEN, the safe is fully operational.
View Battery Status: To check the battery level directly from the keypad, press and hold the '5' key for 3 seconds.
Keys from '1' to '4' will glow GREEN or RED to indicate the battery level. See pages 05 to 06 for more information.
If 4 keys glow green: 80%-100%
If 1 key glows green: 20%-40%
If 3 keys glow green: 60%-80%
If 1 key glows red: 10%-20%
If 2 keys glow green: 40% - 60%
If 1 key blinks red: less than 10%
Toggle Low Battery Alarm: Your safe features a low battery alarm that will sound when the safe is low in battery,
and will sound continually every 8 minutes until the battery dies. To toggle press and hold keys '1' '2' and
"PROGRAM" button together. If the keypad flashes RED, the alarm is disabled; if the keypad flashes GREEN, the
alarm is enabled. The alarm is ON by default.
Toggle Remote Unlock By Phone: The unlock slider to open the safe with the phone app is OFF by default and
will be grayed out. To toggle the unlock slider ON, press and hold keys '1' and '4' and PROGRAM together for 3
seconds. The keypad will flash GREEN to turn the unlock slider ON or RED to indicate the unlock slider is OFF.
13 Vaultek
®
Hot Keys
Continued
Adjust Interior LED Light Duration: Select the desired duration the interior light is ON. To toggle settings press and
hold the '1' key for 3 seconds. The keypad will indicate the selection as below:
Off: Keys (1-5) glow RED
Interior light ON for 10 seconds: Key '2' Green
Interior light ON for 30 seconds: Keys '2' and '3' Green
Interior light ON for 60 seconds: Keys '2', '3', and '4' Green
If the light times out, press the "LIGHT" button inside the safe to extend the light for additional time as selected.
You can also adjust the settings in the Vaultek
®
Bluetooth
Toggle Alert of Manual Unlock: If the Alert of Manual Unlock is ON, and someone opens the safe with either the
key or by picking the lock, the keypad will start flashing and beep for 10 seconds. To clear the alarm you must
enter the authorized master code. To toggle Alert of Manual Unlock press and hold keys '4' '5' and "PROGRAM"
button together for 3 seconds. The keypad will flash GREEN indicating enabled or RED indicating disabled. Alert
of Manual Unlock is OFF by default.
:
Factory Reset
The Factory Reset erases all programmed information and restores the safe to its default settings.
This includes removing any enrolled fingerprints and resetting the master code to 1-2-3-4-5. The safe will need
to be reconfigured again to work with the Vaultek
keys '1' and '5' and "PROGRAM" button together until the keypad flashes green and the safe restarts. Once the
safe restarts remove the battery from the safe, and then put the battery back.
:
Delete Fingerprints (Biometric Model Only)
To delete all fingerprints on the safe press and hold the '1' key and
"PROGRAM" button together at the same time for 3 seconds until all keys (1-5) light up RED, and then enter the
safe's master code. This will remove all the fingerprints. You can delete individual fingerprints in the Vaultek
Bluetooth
app.
®
Dual Entry Mode (Biometric Model Only): Requires input of master code and enrolled fingerprint or vice versa to
open safe. To toggle On/Off press and hold keys '3' and '4' and "PROGRAM" button together for 3 seconds. If the
keypad flashes RED the feature is OFF, if the keypad flashes GREEN the feature is ON. This mode requires that at
least one fingerprint be programmed in the safe.
For Bluetooth Hotkeys including Toggling App Connection ON/OFF visit page 15.
®
app. If the light is toggled OFF the light will be disabled.
®
Bluetooth
®
app. To perform a factory reset, press and hold
®
14 Vaultek
®
Advertisement
Table of Contents
