Enrolling Prints; Securing Your Safe - Vaultek 10 Series Quick Setup Manual

Biometric Scanner: Enrolling Prints 3-20
With both admin prints enrolled, you can enroll additional users. You can store up to 20 different fingerprints.
Tip! When adding additional users after the admin prints, the keypad will flash RED and the LED around the scanner
will illuminate YELLOW. This is prompting the scan of an admin print to authorize the request to enroll a new user.
Open the safe. Program additional fingerprints by quickly pressing and releasing the "PROGRAM" button (Figure L
on page 10). The ring around the fingerprint scanner (Figure M on page 10) will turn YELLOW and the keypad will
flash RED. Scan one of the administrative fingerprints to authorize enrolling a new user then remove when the safe
beeps, keypad flashes GREEN, and the ring around the fingerprint scanner flashes GREEN. You are now ready to
enroll an additional user.
Tip! If the administrative print is left on the scanner too long the safe will begin to program that fingerprint into the
safe again and not the NEW fingerprint. If this happens start over with step one.
Registration Scan 1: While the '1' key is blinking RED, place the new finger on the fingerprint scanner for the first of
5 scans. When the safe beeps and the '1' key lights up GREEN remove your finger.
Registration Scan 2: While the '2' key is blinking RED, place the same print at a slightly different angle (see Figure I
on page 09) until the safe beeps and the '2' key lights up GREEN and lift.
Registration Scan 3: While the '3' key is blinking RED, place the same print at a slightly different angle until the safe
beeps and the '3' key lights up GREEN and lift.
Registration Scan 4: While the '4' key is blinking RED, place the same print at a slightly different angle until the safe
beeps and the '4' key lights up GREEN and lift.
6
Registration Scan 5: While the '5' key is blinking RED, place the same print at a slightly different angle until the safe
beeps and the '5' key lights up GREEN and lift. This completes enrollment for a new user.
IMPORTANT! Repeat steps 1-6 to continue adding additional prints.
Continue on next page to learn how to delete fingerprints.
11 Vaultek ®
(VS10i and VS20i)
Biometric Scanner: Deleting Fingerprints (VS10i and VS20i Only)
Individual fingerprints can not be deleted from the keypad on the safe. Following this procedure will erase all of the
fingerprints including both administrative fingerprints. If you wish to delete individual fingerprints, you must use the
Vaultek ® Bluetooth ® app. This procedure will not affect the keypad master code.
Press and hold '1' and "PROGRAM" button together until all the keys (1-5) light up RED and enter your master code. If
the code is correct, all the numbers on the keypad will blink GREEN and beep indicating deletion of all the fingerprints.

Securing Your Safe

Your Vaultek ® safe can be secured a few different ways. Included is a security cable to attach your safe to larger
stationary objects. There are also mounting screws included to mount the safe to a flat surface using the
pre-drilled holes on the bottom.
Securing Your Safe: Using the Steel Security Cable
Loop the security cable around a secured object. Run the end of the cable through
the eye of the other end and pull tight around the object. Place the end of the
security cable inside the fully enclosed quick release cable mount inside your
Vaultek ® safe as shown in (Figure N).
Tip! Make sure the safe closes with the cable secured inside the quick release cable mount.
Securing Your Safe: Using the Mounting Screws
Tip! Make sure you have enough clearance for the lid to open properly before mounting the safe.
Position the safe on a flat surface where you want to mount it. Use a pencil to mark the holes for drilling and drill
pilot holes. Position safe in place and install the screws through the safe into pillot holes. Tighten screws.
IMPORTANT! Mounting the safe vertically so that the door flips upward will result in incomplete opening of the
safe due to weight. The door will open if the safe is mounted vertically so that door opens down or to the side.
N
12 Vaultek ®