Table of Contents
Advertisement
Index Sea rch
Your recorder automatically marks
index codes at the beginning of
each recording. This function gives
you quick access to any one of 9
index codes in either direction.
N O TE:
Before starting, make sure the
recorder is in the Stop mode.
ACTIVATE IN DEX SEARCH
1
Press PU SH JO G
control. " ™ 1" or " £ 1" is displayed on screen
and search begins in the corresponding direction.
● To access index codes 2 through 9, press
or
repeatedly until the correct index number is
displayed.
Ex.: To locate the beginning of B from the current
position, press PUSH J OG
To locate the beginning of D from the current
position, press PU SH J O G
● When the specified index code is located, playback
begins automatically.
Insta nt ReV iew
Simply by pressing a single button, the recorder power comes
on, rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
N O TE:
Before starting, make sure that the recorder is off and that the
Timer mode is disengaged.
ACTIVATE IN STAN T
REVIEW
1
Press REVIEW . The recorder power comes on and the
recorder searches for the index code indicating the start
of the last timer-recorded programme. Once it's found,
playback begins automatically.
The front display panel tells you how many programmes
have been recorded. If you have, for example, 3
programmes, " REVIEW" and "3" appear and blink. To
watch the first of the 3 programmes, press REVIEW three
times. The recorder searches and begins playback
automatically. You can access a programme as far as 9
index codes away from the current tape position.
N O TE:
Instant ReView is not possible while the recorder is in the Timer
mode.
Downloaded from:
https://www.usersmanualguide.com/
( ™ or £ ) on the remote
or
PU SH JO G
twice.
once.
Current position
A
B
C
D
E
F
–2
–1
1
2
3
Index number
N ex t Function M emory
You can set your recorder's power to go off automatically after
£ 2
the tape is fully rewound. Before starting, make sure the
recorder is in the Stop mode.
For Automatic Power Off After Tape Rewind . . .
. . . press REW , then press
N O TE:
If you want the power to be turned off automatically when the
counter reads " 0:00:00" (instead of at the beginning of the
tape), press C. M EM O RY so that the " M" mark appears before
pressing REW .
Counter M emory
Returns to the counter reading of " 0:00:00" to conveniently find
a specific place on the tape automatically.
SET CO UN TER MEMO RY
1
Press C. RESET during playback at a point you wish to
locate later. The counter reads " 0:00:00" . Then press
C. M EM O RY , and " M" appears in front of the counter
digits.
ACTIVATE CO UN TER
MEMO RY
2
When you wish to return to the designated point, press
STO P and then REW or FF .
● The tape rewinds or fast-forwards and stops at about
0:00:00 automatically.
● To cancel Counter Memory, press
Ta pe Position Indica tor
The tape position indicator
appears on screen when, from
the Stop mode, you press FF ,
REW or perform an Index
Search. The position of " 5 " in
relation to " 0" (beginning) or
" +" (end) shows you where you
are on the tape.
" O.S.D." (
pg. 9) must be
set to " ON" , or the indicator
will not appear.
N O TE:
Depending on the type of tape used, there may be times when
the indication is not correct.
13
EN
within 2 seconds.
C. M EM O RY again.
3
+
+
0
1:23:45
Beginning
+
End
Advertisement
Table of Contents
