Table of Contents
Advertisement
Quick Links
A
D
E
L
s
y
s
t
A
D
E
L
s
y
s
Intelligent Battery Charger
Thank you for having chosen one of our products for your work. We are certain
that it will give the utmost satisfaction and be a notable help on the job.
•
General Description:
OUTPUT N°1
Battery module
OUTPUT N°1
Battery module
OUTPUT N°1
Battery module
Charging Level
OUTPUT N°1
Battery module
OUTPUT N°1
Battery module
Vac Ingresso
OUTPUT N°1
Battery module
Application
CB battery charger is a range of microprocessor-power supplies witch correctly charge sealed lead-acid
OUTPUT N°1
batteries at all time maximizing performance and life span.
Battery module
Charge the battery in multi-stage principle, Fast and Trickle and automatically the device, check the battery
quality in a lifetime to prevent any risk of damage to the battery and allow leaving the charger permanently
OUTPUT N°1
connected. Before begin the operations of installation consult the manual.
Battery module
OUTPUT N°1
•
Mains Characteristic
Battery module
•
Nominal Input Voltage: 115 - 230 Vac
OUTPUT N°1
•
OUTPUT 1: for connection to Battery
Battery module
•
Fast and trickle battery charge In according to DIN 41773
•
Signaling: fault status of the battery
OUTPUT N°1
•
Overload and short circuit protections
Battery module
•
Power limited Battery output
•
Safety isolation in according with EN 60950
OUTPUT N°1
•
Degree of protection IP20
Battery module
•
Rail DIN mounting
OUTPUT N°1
Battery module
OUTPUT N°1
Battery module
OUTPUT N°1
Instruction Manual
Battery module
OUTPUT N°1
ADEL system srl Via L. Barchi 9/B, 42124 Reggio Emilia (Italy) – Tel. ++39-0522-345518
Battery module
Fax. ++39-0522-345551 – Internet: www.adelsystem.com
e
m
t
e
m
CB363A
Fault Status
Monitor Led:
•
Fault
•
Diagnosis
Battery Type
Configuration Jumper
CB363A_R2 Eng
Advertisement
Table of Contents
Related Manuals for Adel System CB363A
Summary of Contents for Adel System CB363A
- Page 1 Rail DIN mounting OUTPUT N°1 Battery module OUTPUT N°1 Battery module OUTPUT N°1 Instruction Manual Battery module OUTPUT N°1 ADEL system srl Via L. Barchi 9/B, 42124 Reggio Emilia (Italy) – Tel. ++39-0522-345518 Battery module Fax. ++39-0522-345551 – Internet: www.adelsystem.com CB363A_R2 Eng...
- Page 2 _________________________________________________________Battery Charger Rail mounting: • The module must be mounted in vertical position. • Other modules must have a minimum vertical distance of 10 cm to this power supply in order to guarantee sufficient auto convection. • Mountig scheme: Assembly: pull down the plastic block with a screwdriver, place the CB on the rail and release the plastic block.
- Page 3 _________________________________________________________Battery Charger • Battery Type Configurations Caution: Switch off the system before Setting the jumper. Posizionamento jumper per la carica: Open Lead (Charge): Trickle =2.23 Fast=2.40/cell Sealed Lead (Charge): Trickle =2.27 Fast=2.40/cell Battery Battery Type Type 1 2 3 1 2 3 Sealed Lead (Charge): Trickle =2.25 Fast=2.40/cell Gel Battery (Charge): Trickle =2.30 Fast=2.40/cell Battery...
- Page 4 _________________________________________________________Battery Charger • Standards and Certification Electrical safety The device must be installed in according with EN60950. The device must have a suitable isolating facility outside the power supply unit, via which can be switched to idle. Safety EN IEC 62368-1 General Standard Immunity in according with EN50082-2, level 3, class B Radio interference suppression in according with EN 55011 class A (industrial areas)
Need help?
Do you have a question about the CB363A and is the answer not in the manual?
Questions and answers