Related Manuals for Haier AD160S2SM3FA
Summary of Contents for Haier AD160S2SM3FA
- Page 1 AD160S2SM3FA Move and scrap the air conditioning ..22 0150544327...
- Page 2 Read the precautions in this manual This appliance is filled with R32. carefully before operating the unit. Service indicator; Read technical Read the operator's manual manual The installation and service of this product shall be carried out by professional personnel, who have been trainedand certified by national training organizations that areaccredited to teach the relevant national competency standards that may be set in legislation.
- Page 3 •A brazed, welded, or mechanical connection shall be made before opening the valves to permit refrigerant to flow between the refrigerating system parts. A vacuum valve shall be provided to evacuate the interconnecting pipe and/or any uncharged refrigerating system part. •The maximum working pressure is 4.3 MPa.
-
Page 4: Disposal Requirements
EUROPEAN REGULATIONS IMPORTANT INFORMATION REGA- CONFORMITY FOR THE MODELS RDING THE REFRIGERANT USED Contains fluorinated greenhouse gases covered by the Kyoto Protocol All the products are in conformity with the following European provision: R32/R410A -Low voltage Directive -Electomagnetic CompatibilitY ROHS The products are fulfilled with the requirements in the directive 2011/65/EU... - Page 5 o not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer. he appliance must be stored in a room without continuously operating ignition sources(for examples: open flames, an operating gas appliance or an operating electric heater).
- Page 6 Cautions Disposal of the old air conditioner Disposal of the packaging of your new air conditioner Safety Instructions and Warnings...
- Page 7 Cautions - The installation of pipe-work shall be kept to a minimum. - Pipe-work shall be protected from physical damage and shall not be installed in an unventilated space, if that space is smaller than Amin(2m2). - Compliance with national gas regulations shall be observed. - Mechanical connections shall be accessible for maintenance purposes.
-
Page 8: Safety Precautions
Safety Precautions CAUTIONS FOR INSTALLATION CAUTIONS FOR TRANSFER OR REPAIR WARNING... - Page 9 Safety Precautions CAUTIONS FOR OPERATION WARNING CAUTION...
- Page 10 3mm. 8. The indoor unit installation height is at least 2.5m. 9. A leakage breaker must be installed. For AD160S2SM3FA ,we can get the 10 different ESP through adjust wired controllerYR-E17,please refer below: static presssure grade (factory default)
-
Page 11: Indoor Unit Pcb
Installation Manual For Wire Controller 5. Wiring connections of wire controller: There are three methods to connection wire controller and the indoor units: A.One wired controller can control max. up to 16 sets of indoor units, and 3 pieces of polar wire must connect the wire controller and the master unit (the indoor unit connected with wire controller directly), the others connect with the master unit through 2 pieces of polar wire B. -
Page 12: Heating Mode
Heating Mode "HOT KEEP" function Warming operation... -
Page 13: Care And Maintenance
Care and Maintenance Points to observe CAUTION Cleaning the air filter CAUTION Care and Cleaning of the unit Post-Season Care Pre-Season Care... -
Page 14: Troubleshooting
Troubleshooting Unit fails to start Cooling or heating is not sufficient Cooling is not sufficient... - Page 15 Troubleshooting The followings are not malfunction...
-
Page 16: Indoor Unit Trouble Shooting
INDOOR UNIT TROUBLE SHOOTING LED flash times Wired Contents of Possible reasons of indoor PCB controller Malfunction display LED4 LED3 Sensor disconected or brok- Malfunction of indoor en,or at wrong position,or unit ambient temper- short circuit ature sensor Malfunction of indoor Sensor disconected or brok- unit piping temper-... -
Page 17: Precaution For Installation
Precaution for Installation WARNING CAUTION... -
Page 18: Is The Unit Installed Correctly
Is The Unit Installed Correctly Installation place Electric work When you change your address or the installation place For inspection and maintenance... -
Page 19: Installation Procedure
(When installing at a place under a high humidity environment, pay sufficient attention to the prevention of dewing such as thermal insulation of the unit. ) Ceiling height shall have the following height. Installation space 100mm 100mm AD160S2SM3FA 50mm Combination 366mm with silent panel Obstacle Avoid installation and use at those places listed below. - Page 20 Installation Procedure Indoor Unit 1. Preparation for suspending the unit a.Size of hole at ceiling and position of hanging bolts AD160S2SM3FA Dimensions A(mm) B(mm) C(mm) D(mm) E(mm) F(mm) Model AD160S2SM3FA 1562 2012 2072 b.Hanger bolts installation 2.Installation of indoor unit...
- Page 21 Installation Procedure Drain Pipe Drain Piping Good piping Improper piping The size of drain opening Unit model For unit without water pump 25mm AD160S2SM3FA For unit with water pump...
- Page 22 Installation Procedure Drain Pipe Drainage Test Procedures Installation Procedure Air Duct Installation work for air outlet ducts Note Connection of suction, exhaust ducts a.Fresh air inlet b.Exhaust (Make sure to use also the suction.)
-
Page 23: Move And Scrap The Air Conditioning
Selection of size of power supply and interconnecting wires Select wire sizes and circuit protection from table below. (This table shows 20 m length wires with less than 2% voltage drop.) AD160S2SM3FA POWER SUPPLY & INDOOR-OUTDOOR CONNECTION: Make wiring to supply power to the outdoor unit, so that the power for the indoor unit is supplied by outdoor unit terminal blocks. - Page 24 Address:Haier Industrial Park,Qianwangang Road,Eco-Tech Development Zone,Qingdao 266555,Shandong,P.R.C. Contacts: TEL +86-532-88936943; FAX +86-532-8893-6999 Website: www.haier.com...