Advertisement
TE-4021
Tinytag Plus LAN Temperature Data Logger for Thermistor Probes
LED Flash Patterns
Ethernet Radio Receivers and LAN data loggers have two status LEDs; one to
show the status of the logger's Ethernet connection (yellow/blue) and the
second to show the status of the unit (green/red).
Action
LED
n/a
No Indicators
n/a
Red flash every 4
seconds
n/a
Green flash every 4
seconds
Press and briefly
Green indicator
hold the mute
shows for one
switch.
second. It then
briefly flashes green
then red.
Press and hold the
Red indicator shows
mute switch for 3
for one second.
seconds.
n/a
Yellow indicator on
constantly
n/a
Blue (flickering)
Note that the yellow and blue LEDs cannot be on at the same time. If the
blue LED is on (or flickering) then PoE power must be available.
Calibration
This logger is configured to meet Gemini's quoted accuracy specification
during its manufacture.
We recommend that the calibration of this unit should be checked annually
against a calibrated reference meter.
A traceable certificate of calibration can be supplied for an additional charge
either at the point of purchase, or if the unit is returned for a Service
Calibration.
Warranty
This product carries a manufacturing defects warranty of 12 months from the
date of purchase. Units returned under warranty will be repaired or replaced at
the manufacturer's discretion. This warranty does not cover mishandling,
modification or battery replacement and is subject to our standard Terms and
Conditions of Sale, a copy of which can be found at www.tinytag.info.
BERMAN Termómetros e Instrumentación S.L.
ventas@e-berman.info
Telf. 93 263 24 50
Status/Operation
Device is powered off
The device is powered on and
has a problem.
Either:
a) Battery is low or
b) An alarm indicator is
signalled.
Check the nature of the
problem using Tinytag
Explorer.
The device is powered on, and
does not have any problems.
The device has been switched
on.
The device has been switched
off.
The device is being powered
from its Ethernet connection,
but no communications have
been established.
Ethernet communications are
established and on-going
Approvals
Gemini Data Loggers (UK) Limited hereby declares that this data logger is in
compliance with the essential requirements and other relevant provisions of
EMC directive 2014/30/EU and RoHS directive 2011/65/EU. A copy of the
declaration of conformity is available upon request.
This logger also conforms to the following EMC standards EN 61326-1:2013,
FCC/CFR 47:Part 15:2016 & Canadian Standard ICES-003:Issue 6.
This logger also complies with (RJ45) 10/100Mb Base-T for Ethernet
connectivity and PoE standard IEEE 802.3af.
Gemini Data Loggers (UK) Ltd. operates a Business Management System
which conforms to ISO 9001 and ISO 14001.
Required and Related Products
Required Parts
Two Ethernet cables (not supplied) are required to connect this receiver
to a LAN.
This logger is a PoE device and is supplied with a PoE injector as standard. If
the logger is being used on a powered network, or a number of loggers are
being connected to a powered hub, this product can be supplied without the
injector.
When used as a standalone device, a copy of the following software is
required:
SWCD-0040 Tinytag Explorer
When used as part of a Tinytag Connect system, a copy of the following
software is required:
SWCD-0080 Tinytag Explorer Connect
Probes
You will also require one of the following probes:
PB-5001-1M5/3M Standard Thermistor Probe or
PB-5002-1M5/3M Fast Response Thermistor Probe or
PB-5003-1M5/3M Surface Thermistor Probe
Other types of thermistor probe are available. Please contact your supplier for
further information.
Further Related Products
ACS-0040 RJ45 waterproof (IP67) Shroud (supplied)
ACS-0041 PoE Injector (supplied)
CAB-0041 Plus LAN alarm output lead
www.e-berman.info
Issue 1 (16th June 2017) E&OE
Advertisement
