Page 1
User’s Guide L197WHP ake sure to read Important Precautions before using this product. Keep the User's Guide (CD) in an accessible place for future reference. ee the attached label on the unit and show this information to your dealer when asking for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety; however, improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
Page 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Unfolding the stand base Place the monitor with its front facing downward on a soft cloth. Hold the stand base and lift it up following the sequence as shown in the picture.
Connecting the Display Folding the stand base Face the front of the monitor dislpay. Then gently push the monitor backwards, following the sequence shown in the picture below. Tilt range Make sure that the angle of the panel is set for your comfort. Tilt Range : 0˚~30˚...
Page 6
Connecting the Display To adjust the height Scope of adjusting the height -L197WHP : maximum 4.76 inches (121 mm) 121 mm...
Connecting the Display Using the Computer Make sure to turn off the computer and the product. Connect the cable as below in the sketch map form Connect DVI Cable Connect Dsub Cable (PC) Connect Dsub Cable (Mac) NOTE This is a simplified representation of the rear view.
Connecting the Display To arrange the cables Insert and screw the cable holder into the hole in the back of the stand until it will not turn any more as shown in the following figure. After connecting the cables neatly, arrange the cables in the Cable Holder as shown in the following figure.
The resolutions at which the EZ ZOOMING operates are as follows: L197WHP: 1440 x 900, 1280 x 1024, 1024 x 768, 800 x 600 The setting method can differ by O/S or video card. In this case, Please ask the computer or...
Page 10
(display mode). The best display mode is L197WHP : 1440 x 900 Power Button Use this button to turn the display on or off. This Indicator lights up as blue when the display is Power Indicator operating normally (On Mode).
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the display's image size, position and operating parameters is quick and easy with the On Screen Display Control system (OSD). A short example is given below to familiarize you with the use of the controls.
Page 12
On Screen Display (OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu Reference BRIGHTNESS PICTURE To adjust the brightness, contrast and gamma of the CONTRAST screen GAMMA sRGB To customize the color of COLOR PRESET...
On Screen Display (OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
Page 14
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description PICTURE To adjust the brightness of the screen. BRIGHTNESS P I C T U R E To adjust the contrast of the screen. CONTRAST Set your own gamma value. : -50/0/50 GAMMA On the monitor, high gamma values display whitish images and low gamma...
Page 15
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description POSITION To move image left and right. HORIZONTAL P O S I T I O N To move image up and down. VERTICAL MENU : Exit : Decrease : Increase : Select another sub-menu TRACKING...
Page 16
640x480 4 : 3 720x480 3 : 2 The input signal which the 4:3 IN WIDE does not support '4:3' mode is the following. - L197WHP: 720x400,1280x768,1360x768,1440x900. Restore all factory default settings except FACTORY "LANGUAGE." RESET Press the button to reset immediately.
On Screen Display (OSD) Selection and Adjustment The OSD screen will appear when you touch the (-) button on the front of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown.
Troubleshooting Check the following before calling for service. No image appears No image appears ● Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. ● Is the power on and the •...
Troubleshooting Display image is incorrect ● Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display.
Troubleshooting Display image is incorrect ● The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. Place the monitor with its front facing downward on a soft cloth or a cushion. Gently hold Cover Hinge Cap with hands as shown in the picture. Then, lift it up and separate from the body.