Jiecang JCA User Manual

AC Tubular Motor with Zigbee
User Manual
01 Product Info
Motor Head Button(H) Working temperature
Power wire
LED
Zigbee Antenna
RF Antenna
Remote Controller Buttons
Power Options
Blue Line: N
Brown Line: L
LED
Green/Yellow Wire: E
220V/50Hz
Stop Up
CH- CH+ White Line: N
Red Line: L
Green Line: E
Down
Fav
Prg
110V/60Hz
Models & Parameters (for details about other parameters, see the product nameplate)
JCA 35 S E 100 17 Z
Tube Diameter: 35 mm S:Standard Torque: 10Nm
AC Motor E: Electric limit 230V/50Hz Speed: 17Rpm Built-in Zigbee module
EL: Electric limit 110V/60Hz
02 Caution!
1. The power supply is AC supply.
2. Please confirm the rated voltage and frequency according to the nameplate when using it.
3. The motor will jog in operation, please do not proceed to the next step until it complete.
4. During operation, the effective interval of the transmitter button operation is 10 seconds.
If there is no effective transmitter operation for more than 10 seconds, it will automatically
exit the current mode.
5. The motor can be paired with max 10 controllers.
6. Upper&Lower limits cannot be set at the same position, limits saved even power off.
7. The motor runs constantly for at 6mins max without any other operation.
8.Do not lift the motor by grabbing the wire or antenna.
03 Instructions
Motor head button (H) functions
Jogging LED lamp
Functions Operation
time flickers
Control the UP/STOP/
/
Short press
DOWN of the Shade
Adding/Removing
Jog*1
Hold for 2s Flicker*1
Controller
Zigbee Connecting Flicker*2
Hold for 6s Jog*2
Direction Reverse Hold for 10s Jog*3 Flicker*3
Reset Hold for 16s Jog*4 Flicker*4
a.Pairing Motor with Controller
55℃
-10℃
After motor is powered on for more than 10s
H button
Note: Pairing can not be done under group channel or 0 channel.
b.Direction Reverse
Note
Can only operate after
/
the limits are set
Operation needs be
c.Upper&Lower Limits Setting
done within 10s
Entering Zigbee
connection mode
or
All settings saved after
direction reversed
Up or Down Fix upper point
All settings deleted
or
Up or Down Fix lower point
Note: Upper&Lower limits cannot be set at the same point.
Before limits set, the motor will run in one-touch mode by pressing Up or Down,
hold Up or Down for 2s, motor runs in constant-touch mode.
Once limits set, press Up or Down, motor runs in constant-touch mode.
d.One-touch/Constant-touch Mode
Constant-touch ------>One-touch
P
Prg Jog x1 Stop
Same operation can toggle from one-touch to constant -touch mode.
Note: When motor in one-touch mode, hold Up or Down for more than 2s, it will run in
constant-touch mode.
e.Setting and Cancelling Favorite Position
Setting
or
Fix Fav.
Up or Down
position
Cancelling
&
Fav & Stop x2s
Shade is at
Fav. position
f.Hot key to the Fav. Position
Fast get to the Fav. point
Fav
Note: The Fav. position setting only can be done after upper&lower limits set.
g.Adjusting Upper & Lower Limits
Adjust Upper limit
&
Up & Fav x6s
Jog x2
Adjust Lower limit
&
&
Up & Fav x2s Jog x2 Upper
limit set
Down & Fav x6s
&
Jog x2
Down & Fav x2s Jog x2 Lower
limit set Note: The operation should be done within 4mins.
h.Removing Controllers
Remove a single controller
H button
H button x2s
OK
Remove controller B via pre-existing controller A
Jog x1 Stop Jog x1
P
Prg on
existing A
Controller B removed
Remove all controllers:
&
P
Fav & Stop x2s Fav. position
Jog x2 Prg
set
All controllers removed
Note: All the settings are saved even controllers removed(limits set are saved).
Controller A/B are already paired to motor.
Jog x1 Fav. position
Cancel
i.Cancelling Limits
P
Prg
Limits cancelled
Note: It is forbidden to run the motor if installed into the shade without limits.
Limits should be set immediately to protect the shade.
or
&
Jog x1
Up or Down Fix new Up & Fav x2s
upper limit
OK
or
&
Jog x1
Up or Down Down & Fav x2s
Fix new
lower limit
OK
OK
P
Jog x1 Prg Jog x1
P
Jog x1 Prg on Jog x1 Stop on B Jog x1
existing A (to remove)
P
Jog x1 Prg Jog x1 Down Jog x1
P
Jog x1 Stop Jog x1 Prg Jog x1