CONDTROL SMART 20 - Laser Distance Meter Manual

CONDTROL SMART 20 - Laser Distance Meter Manual

Advertisement

CONDTROL SMART 20 - Laser Distance Meter Manual

FUNCTIONS/APPLICATIONS

Laser distance meter SMART 20 is intended to measure distance at indoor building areas.

PACKAGE

  1. Laser distance meter – 1pc.
  2. Batteries (type ААА) - 2 pcs.
  3. User manual – 1 pc.

SPECIFICATIONS

Working range 0,2...20m*
Smallest unit displayed 1mm
Measuring accuracy ±3mm**
Laser type Class II, 630-670nm, < 1mW
Continuous measurement (tracking) +
Display backlight +
Automatic shutdown of laser 30sec.
Automatic shutdown of laser distance meter 180sec.
Storage temperature -10...+60°С
Working temperature 0...+40°С
Battery 2 х 1.5V AAA LR3 (alkaline)
Battery life up to 5000 measurements
Dimensions 100х40х25mm
Weight 80g

* Use a reflecting plate to increase the measurement range during daylight or if the target has poor reflective properties.
** In favorable conditions (good target surface properties, room temperature) up to 10 m. In unfavorable conditions, such as intense sunshine, poorly reflecting target surface or considerable temperature variations, accuracy can decrease at distance over 10m

PRODUCT DESCRIPTION

PRODUCT DESCRIPTION

Display

  1. Main display line
  2. Secondary display line
  3. Battery charge level
  4. Measuring unit
  5. Laser beam indication
  6. Reference point

OPERATION

Insert/replace batteries
Remove the battery cover. Insert the batteries, observing correct polarity. Put the battery cover back. Remove the batteries when the device is not used for a long time to avoid corrosion and battery depletion. Both batteries should be replaced at the same time. Both batteries must be of the same brand with the same charge level. Replace batteries when you see symbol on the display.

Switch on/off
Switch on: press and hold for 1 sec. button .
The device will turn on and enter single distance measuring mode. Laser beam will turn on simultaneously. Laser beam automatically turns off in 30 seconds after the last operation.
Switch off: press and hold for 1 sec. button .
In order to save battery power the device will switch off automatically within 3 minutes after the last operation.

Display backlight
When the device is on, backlight turns on automatically when you press button . The backlight will turn off automatically in 10 seconds after last operation.

Reference point
Reference point is the bottom end of the device.

Measuring unit.

Press simultaneously buttons and to select the reference point – m (meter) or ft (foot).

MEASUREMENTS

  1. Single distance measurement
    Short press button to switch on the device. Laser beam will be on. Point the laser beam at the target and short press button for single distance measurement. The result of measurement will appear in the main line on the display. To perform next single distance measurement press button to turn on the laser beam and then press again.

  1. Continuous measurement (tracking)
    When in single distance measurement mode press and hold for 1 sec. button . The device will take measurements one after the other, showing the last measured value. To stop continuous measurement press button or . To exit the mode short press .

MESSAGE CODES

While operation, the following codes/symbols may appear on the display:

Message Cause Solution
204 Calculation error Refer to user manual, repeat the procedure.
208 Excessive current Please contact the distributor or authorized service center.
220 Batteries are low Replace the batteries.
252 Operating temperature is too high Cool down the device to temperature within 0...+40 0 С.
253 Operating temperature is too low Warm up the device to temperature within 0...+40 0 С
255 Received signal is too weak Make measurements against surface with better reflective properties. Use a reflecting plate.
256 Received signal is too strong Make measurements against surface with lower reflective properties. Use a reflecting plate.
261 Outside of measuring range Carry out measurements within the range acceptable for this device.
500 Hardware error Switch on/off the device several times. If this error still appears, please contact the distributor or authorized service center.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download CONDTROL SMART 20 - Laser Distance Meter Manual

Advertisement

Need help?

Need help?

Do you have a question about the SMART 20 and is the answer not in the manual?

Questions and answers

Table of Contents