Advertisement
Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly.
9
Ensure the output of the charger is the same voltage as the battery.
9
Ensure that during charging, the charger is placed in a location where there is sufficient ventilation to prevent the build up of explosive
9
gases from a lead acid battery, and DO NOT cover or obstruct the charger ventilation louvres.
If battery has caps to access the battery fluid, remove the caps and check the fluid level before connecting the power clamps.
9
If necessary top-up the battery with distilled water by referring to the battery manufacturer's instructions (Apply the personal safety
9
precautions described in part 1.3).
9
If the charger receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
If the battery terminals are corroded or dirty clean them before attaching the power clamps.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT dis-assemble the charger for any reason. The charger must only be checked by qualified service personnel.
8
DO NOT try to charge a non-rechargeable battery.
8
DO NOT try to charge battery if battery fluid is frozen.
8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
DO NOT allow power clamps to touch each other or to make contact with any metallic part of the vehicle.
8
DO NOT cross connect power leads from charger to battery. Ensure positive (+/RED) is to positive and negative (-/BLACK) is to negative.
8
DO NOT pull the cables or clamps from the battery terminals.
8
DO NOT use the charger outdoors, or in damp, or wet locations and DO NOT operate within the vicinity of flammable liquids or gases.
8
DO NOT use charger inside vehicle or inside engine compartment.
8
Ensure there is effective ventilation to prevent a build-up of explosive gases, and DO NOT cover or obstruct charger ventilation louvres.
9
DO NOT use the charger for a task for which it is not designed.
8
WARNING! DO NOT simultaneously charge batteries of different capacities or discharge levels.
‰
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
‰
When not in use, store the charger carefully in a safe, dry, childproof location.
9
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
2.
INTRODUCTION
i
Automatic battery charger & starter, designed for charging, maintaining, and boosting a variety of AGM (stop/start), GEL, lead acid and Lithium
LiFePO4 batteries up to 300Ah. Intuitive digital display and 150A peak engine start function, makes this unit ideal for every workshop. Features
overcharge, short circuit, and reverse polarity protection. Dedicated charging programs for AGM, GEL and conventional lead acid batteries with fully
automated charging algorithms. Fast charge program for larger batteries. Automatic boost/engine start function once 12V mode is selected and
battery voltage is over 4V. Portable design with carry handle and cable management system which allows the clips to be stored neatly away when
not in use.
3.
SPECIFICATION
i
Model No:
Supply:
Output Charge:
Start Current:
Peak Current:
Battery Range:
Cable & Clamp Length:
Insulation Class:
4.
OPERATION
i
4.1.
DISPLAY
© Jack Sealey Limited
Superboost150D
230V
6V - 2A, 12V - 2A(L)/15A(H) (15A LiFePO4)
12V - 75A (5s on 180s off)
150A
30-300Ah
1.2m
IP20
Original Language Version
SUPERBOOST150D Issue 2 (3)
12/12/22
Advertisement
