Page 2
Thank you for purchasing STB10HD Digital High Definition Set Top Box. This manual will help you to install, use and m aintain the receiver. Please read this manual carefully before operating your unit and keep it for future reference. Warning & Note In this manual, pay special attention to the following marks that indicate hazardous situations.
Page 3
User’s Manual Safety Instruction Read following items carefully before operating this receiver. Installation This receiver should be installed horizontally. Unbalanced installation may cause damage. Install the receiver in a place with: good ventilation (leave space not less than 10cm around this receiver) no heat source (burning candle, radiator, heater, fireplace, amplifier, etc) suitable temperature against humidity (especially bathroom, kitchen, etc)
Page 4
User’s Manual RCU Battery Batteries should be installed in accordance with the (+/-) markings on battery compartment. Remove batteries if RCU not be used for a long time. Replace batteries if there is no enough power and dispose battery waste properly for environmental protection.
User’s Manual Contents 1. Before Using the Receiver ....................2 1.1 Main Feature ......................... 2 1.2 Front Panel ........................3 1.3 Rear Panel ........................4 1.4 Remote Control Unit (RCU) ..................5 2. Installation ..........................7 2.1 Connect TV ........................7 2.2 Connect other Device ....................
User’s Manual 1. Before Using the Receiver 1.1 Main Feature Dolby 5.1 supported MP3 play and picture browse Teletext/subtitle supported EPG supported 16 favorite channel groups Memory space up to 1000 channels Support automatic, manual scan Powerful channel edit function Parental control supported Software upgrade supported Standby with low power consumption...
User’s Manual 1.2 Front Panel Name Function Switch between operation and standby modes (In standby 1. STAND BY mode, the receiver is disconnected with power supply.) Receive infrared remote control signal 2. SENSOR Display status 3. DISPLAY Open the cover to insert specific USB device 4.
User’s Manual 1.3 Rear Panel Name Function Output CVBS video signal to TV 1. VIDEO Output Y/C video signal to TV 2. S-VIDEO Output Y/Pb/Pr video signal to TV (support high definition output) 3. Y/Pb/Pr Output left/right audio signal to TV or amplifier 4/5.
User’s Manual 1.4 Remote Control Unit (RCU) Name Function 1. Learning keys Please refer to Learning Key. 2. The keys of the receiver Switch between operation and standby modes (In standby mode, the receiver is disconnected with power supply.) Mute/restore sound Switch between TV and radio modes TV/RADIO Switch channels or input numbers...
Page 10
User’s Manual Learning Key The receiver RCU has some learning keys at the lower part. The keys (except SET key) can be used to memorize corresponding key values of TV RCU. After learning, you can realize remote control for TV with the receiver RCU. The recommended keys are POWER, TV/AV, VOL+ and VOL- of TV RCU.
User’s Manual 2. Installation Connect TV and other devices, then you can power on the receiver and scan channels. 2.1 Connect TV Please choose one of following 4 ways to connect TV. 1. Connect TV Using RCA Cable 1. Connect ANT IN port on the receiver to terrestrial antenna with an RF cable. 2.
Page 12
User’s Manual 3. Connect TV Using YPbPr Cable 1. Connect ANT IN port on the receiver to terrestrial antenna with an RF cable. 2. Connect Y/Pb/Pr ports on the receiver to Y/Pb/Pr ports on TV. 3. Connect R/L-AUDIO ports on the receiver to corresponding ports on TV.
User’s Manual 4. Connect TV Using HDMI Cable 1. Connect ANT IN port on the receiver to terrestrial antenna with an RF cable. 2. Connect HDMI port on the receiver to HDMI port on TV. 2.2 Connect other Device For connection of other devices, please refer to following figure: Connect LOOP OUT port on the receiver to ANT IN port on another receiver.
User’s Manual Note: If you encounter any problem during the connections, please contact your local operator. 2.3 Power on 1. Connect the power cord of the receiver to wall outlet. 2. Turn on the receiver, and system initializes. If you turn on the receiver for the first time, an installation guide appears on screen.
User’s Manual 3. Basic Operation This part describes operations such as channel switch, volume control and other basic operations when playing program. 3.1 Channel Switch You can switch channels using the following methods: A. Press or CH+/- keys to switch channels. B.
User’s Manual 3.4 Channel List Channel list is available for you to browse channels easily and quickly. 1. Press OK key to display channel list. 2. Press TV/RADIO key to switch between TV and radio modes. 3. Press keys to select a channel. 4.
User’s Manual 4. Electronic Program Guide (EPG) In this guide, you can view program information based on date and time. In addition, the guide can help to schedule future programs. 4.1 Full Guide The full guide displays detailed EPG information. Select Main Menu →...
User’s Manual 4.3 Remind List All the scheduled programs are displayed in this window. You can cancel or restore schedules. Select Main Menu → Guide → Remind List and press OK key to enter. 1. Press keys to select a schedule. 2.
User’s Manual 6. Channel Scan Note: Don’t turn off the receiver during scanning. 6.1 Auto Scan For beginners, auto scan is the best choice. System will scan channels according to default frequency parameters. Select Main Menu → Scan → Auto Scan and press OK key to enter.
User’s Manual 7. Channel Edit You can set favorite channels. In addition, you can rename, sort, add, delete, move and search channels. Select Main Menu → Channel → TV/Radio Channel List and press OK key to enter. 7.1 Set Favorite Channel 1.
User’s Manual 7.4 Add/Delete Channel 1. Press number key 4 to enter add/delete mode. 2. Press keys to select a channel. 3. Press OK key to delete this channel, and “CH Deleted” is displayed in top left corner of screen. If you want to resume this channel, press OK key again.
User’s Manual 8. Setup 8.1 System Setting Select Main Menu → Setup → System Setting and press OK key to enter. 1. Set parameters as follows: OSD Language: The default is “English”. OSD Theme: Press keys to select a color for menu.
Page 23
User’s Manual 1. Lock Channel You can set channel lock to restrict viewing of some channels. Highlight “Lock Channel” and press OK key to display lock channel window. Lock a Channel 1. Press keys to select a channel. 2. Press OK key to lock this channel, and mark it with “...
User’s Manual Allow all Programs 1. Press arrow keys to highlight “Allow All”. 2. Press OK key to confirm, and all ratings are unblocked. 3. Press EXIT key to save and exit. Note: The system lock password is required to view programs beyond set rating. 3.
User’s Manual 10. Software Upgrade by USB Warning: Don’t turn off the receivers during software upgrade. Select Main Menu → Setup → Upgrade by USB and press OK key to display upgrade by USB window. Note: USB device should be connected to USB port on front panel before operation.
User’s Manual 11. Appendix 11.1 Trouble Shooting DISPLAY on front panel is off 1. Power cord is disconnected. Make sure power cord is plugged into a proper power socket. 2. The receiver is turned off. Turn it on. DISPLAY on front panel is on, but no sound and picture on TV screen The receiver is in standby mode.
User’s Manual 11.3 Acronym CVBS Composite Video Broadcast Signal Digital Video Broadcasting Electronic Program Guide Free to Air HDMI High Definition Multimedia Interface HDTV High Definition Television Logical Channel Number Low Noise Block Multiplexer Network Information Table On Screen Display Packet Identifier Radio Corporation of America Radio Frequency...