Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Giada IBC-386
Summary of Contents for Giada IBC-386
- Page 2 The copyright of this manual belongs to Shenzhen JIEHE Technology Development Co., Ltd. (Giada, JIEHE’s global brand) and all rights are reserved. The company reserves the right to change this manual at any time without notification. Specifications here are for reference only, please take the real product as standard.
-
Page 3: Table Of Contents
Table of Contents 1. Product Introduction ................2 2. Hardware Specifications ..............2 3. Hardware Usage Instruction ............... 4 3.1 Dimensions Chart ................4 3.2 Interface Definition ................4 3.2.1 Jumper, Header and Interface Diagram ........4 3.2.2 Jumper and Header Definition..........5 3.3 Accessories Installation Steps ............ -
Page 4: Product Introduction
1. Product Introduction Embedded motherboard IBC-386 adopts RK3399 Dual-core Cortex-A72 and Quad-core Cortex-A53 CPU. With one LVDS, one HDMI display output, it supports 4K resolution. The board is suitable to be applied in all-in-one digital signage solution, kiosk and smart control applications. - Page 5 3 x USB2.0 Signal by 3 x 4 pin USB Header 2 x USB2.0 Signal by 1 x 8 pin USB Header 1 x 20 pin eDP Display 1 x 30pin dual channel 24bit LVDS (Max.1920×1200@24 Hz) Camera 1 x MIPI-CSI Jack Serial Port 3 x 4 pin RS232 Header, 1 x 4 pin RS485 Header, 1×4 pin TTL Internal I/O...
-
Page 6: Hardware Usage Instruction
3.Hardware Usage Instruction 3.1 Dimensions Chart 3.2 Interface Definition 3.2.1 Jumper, Header and Interface Diagram - 4 -... -
Page 7: Jumper And Header Definition
3.2.2 Jumper and Header Definition Jumper Function PIN Definition /Header MCU-DEBUG MCU DEBUG JUSB4 USB2.0 pin RS232(TTL) RS232 pin ttyXRUSB0 RS232 RS232 pin ttyXRUSB1 RS485 ttyXRUSB3 RS485 pin - 5 -... - Page 8 RS232 RS232 pin LED/IR LED/IR pin MIC pin 2PIN SPK_B（4Ω Speaker pin 10W） 4PINSPK Speaker pin (8Ω 10W） LVDS LVDS pin - 6 -...
- Page 9 LVDS_PWR_SEL LVDS Power Select EDP pin EDP_PWR_SEL EDP Power Select F_TTL F_TTL pin EDP_BL EDP Invt1 - 7 -...
- Page 10 LVDS_BL LVDS Invt1 TP_I2C I2C touch pin JUSB2 USB2.0 pin JUSB3 USB2.0 pin JUSB1 Dual USB2.0 pin - 8 -...
-
Page 11: Accessories Installation Steps
GPIO GPIO pin 3.3 Accessories Installation Steps For safety reasons, please ensure that the board is disconnected with power before installation. 3.3.1 3G/4G Installation 1. Plug the 3G/4G module into the mini PCIE slot. 2. Secure the module to the carrier by tightening up the screw. 3.3.2 SIM Card Installation This product supports standard SIM card with the size of 25mm ×... -
Page 12: Firmware Upgrade Guide
Host PC with screen and installed the Windows operation system. USB OTG Cable (RP-SMA Male↔RP-SMA Male). After you get the Archive from Giada technical support, copy the Archive to your host PC, you will find below files inside: ... -
Page 13: Upgrade The Firmware
4.2 Upgrade the firmware 4.2.1. Install the driver in your host PC by following steps: a. Click the DriverAssitant file. Launch RK DriverAssitant and press “Install Driver”. b. Apply all changes and warnings during the installation. c. Click “ok” after the installation finish 4.2.2. - Page 14 a. Please ensure that the power of the motherboard is disconnected. b. Run Android tool V2.84 under the windows of the host PC. c. Connect motherboard to the host PC via usb OTG port. Firstly, hold the motherboard Uboot button (please refer to fig1 for the location of the button), then connect the power adaptor to the motherboard, you will see “Found a MSC Device”...
-
Page 15: Start The Firmware Updating
(Fig2) 4.2.3. Start the firmware updating a. Click “Firmware” button and specify the path to the firmware file which is stored in the host PC (Please refer to Fig2). b. Wait around 5 seconds to upload the program, FW information will display on the screen. After the “Upgrade”... -
Page 16: Jahc App
The user can set up automatic startup and shutdown, one week as a circle. 5.2 Startup(open) & shutdown(close) time setup System Requirements: Giada player with JAHC APP function. Android OS includes JAHC APP（please refer to Fig1）. - 14 -... - Page 17 (Fig1) a. After enter the android desktop, click the JAHC APP icon and the JAHC interface will pop up (please refer to Fig2) (Fig2) b. Click “New” button to set open time (Fig3) and then click Close time button to set close time.
- Page 18 (Fig3) (Fig4) (Fig5) Caution: If the interval from shutdown time to next resume time is less than 3 minutes, the system will not shut down - 16 -...
- Page 19 - 17 -...
Need help?
Do you have a question about the IBC-386 and is the answer not in the manual?
Questions and answers