1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-1-4. Product Safety Notices Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc.
1. Precautions 1-2. Servicing Precautions An electrolytic capacitor installed with the wrong polarity might explode. WARNING Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. CAUTION If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-3. Static Electricity Precautions Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
Page 10
ANNEX. Exploded View & Part List ANNEX. Exploded View & Part List [UN60JS7000FXZA-MD01] 1-1. Exploded View ANNEX-1...
Page 11
ANNEX. Exploded View & Part List 1-1-1. Parts List Code No. Description & Specification Q’ty SA/SNA Remark BN95-02449A PRODUCT LCD-SHARP; CY-TJ060HGSV1V,JS6900, BN96-38492B ASSY CHASSIS TOP P; JS6.9K_60,PC+GF,DARK BN95-02371C ASSY COVER STAND SMT; J6200,60,DARK TITAN BN96-35006B ASSY SPEAKER P; 6ohm,4pin,10W,JU7000 60" BN44-00860A DC VSS-LED TV PD BD;...
Page 12
ANNEX. Exploded View & Part List 2-1. Electrical Parts List Service Bom (SA: SERVICE AVAILABLE, SNA: SERVICE NOT AVAILABLE) Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark UN60JS7000FXZA (MD01) BN90-06530S ASSY W/I;LED_J6K BN81-08159Z PART SET-ELEC W/I;UF**,UH**,UG**,ELEC BN81-12183S A/S PART SET-MECH W/I;UJ6J,U60JJ* R001A BN90-07082E...
Page 13
ANNEX. Exploded View & Part List Level Location No. Code No. Description & Specification Q’ty SA/SNA Remark BN39-01990D LEAD CONNECTOR-FUNCTION;JU7K,FLAT Connec LEAD CONNECTOR;FLAT CONNECTOR EC13 BN39-02017B ASS'Y,Lead LEAD CONNECTOR- BN39-02025A POWER;UN40JU6400AFXZA,Fla BN39-02147B LEAD CONNECTOR-JS6900 BLU;BLU,FLAT CONNE P001A BN44-00860A DC VSS-LED TV PD BD;L60SHN_FDY,L60SHN_FD NW01 BN59-01194F NETWORK;11ac Combo,Internal WiFi,USB 2.0...
2. Product specifications 2. Product Specifications 2-1. Product information Model UN**JS7000F Front View * W : Width H : High D : Depth Detail View Front Color Dark Titan Body 1128.9 X 654.4 X 63.2 mm 50" With stand 1128.9 X 719.6 X 310.5 mm Body 1242.6 X 718.4 X 63.2 mm Dimensions...
DTS Premium Sound 5.1 3D Sound Sound Customizer Sound Output (RMS) 20W(L:10W, R:10W) Speaker Type 2CH(Down Firing + Bass Reflex) Woofer HD Audio Wallmount Sound Mode Multiroom Link Smart TV Samsung SMART TV Apps Game Multi-Link Screen ACR (Advertisement) Yes (US Only)
Page 43
Face recognition Ready Motion control Ready Convergence TV to Mobile - Mirroring Mobile to TV - Mirroring Wired(US Only) Samsung SMART View Wireless TV On - WOL Notification - BLE Briefing On TV WiDi WiFi Direct Tuner/Broadcasting Digital Broadcasting ASTC/Clear QAM...
Page 44
Bezel Type Slim Type Slim Front Color Dark Titan Light Effect (Deco) Stand Type V-Shape Swivel (Left/Right) Additional Feature Samsung 3D 3D Converter Instant On Camera Built-in Wireless Copy Processor Quad-Core PX Ready 21:9 Immersive Picture Mode SCSA Support Accessibility...
Page 45
Eco Sensor Accessory 3D Active Glasses (Included) Remote Controller Model TM1260C Batteries (for Remote Control) Samsung Smart Touch Control (Included) PX (Included) Ultra Slim Wall Mount Supported Mini Wall Mount Supported Vesa Wall Mount Supported Floor Stand Support TV Camera (Included)
2. Product specifications 2-3. Accessories NOTE • The items’ colors and shapes may vary depending on the model. • Cables not included in the package contents can be purchased separately. • The part code for some accessories may differ depending on your region. Product Code.
2. Product specifications 2-4. Viewing the Functions The Remote Control NOTE • The button names above may differ from the actual names. • The remote control may differ by its model. • This remote control has Braille points on the Power, Channel, Volume, and Enter buttons and can be used by visually impaired persons.
Page 48
2. Product specifications Displaying and using the On-Screen Remote You can display and use the On-Screen Remote on the TV's screen by pressing MENU/123 button on the Samsung Smart Control. Button Description Menu Displays the menu on the screen.
Page 49
2. Product specifications Button Description Power Turns off the TV. Use these colored buttons to access additional options specific to the feature in use. • These buttons are only available in the U.S.A. and Canada. Move Number Pad to the Moves the number pad to the left or right.
" " 2. Product specifications 2-4-1. Learning motion control basics The following actions are available. Image Description Moving the pointer Move your hand to move the pointer accordingly. Selecting an item Fold down and raise your index finger to select items. You can select a TV menu or run a function.
You can surf the web and download apps with Smart Hub. In addition, you can enjoy photo, video, and music files stored on external storage devices. Place a finger on the POINTER button on the Samsung Smart Control, and then select at the bottom of the screen. • To run Smart Hub while you are using a service provided by Smart Hub, use the same path described above.
Page 52
The genre categories at the top of the screen may differ with the model and geographical area. You can download, play, and manage games or games purchased with your Samsung account. Select a game displayed on the screen or select a genre category such as Spotlight, Most Popular, What's New, or Top Grossing from the top of the screen, and then select a game in the genre you selected.
Page 53
2. Product specifications APPS NOTE • Screen images may differ by model. • To use this feature, the TV must be connected to the Internet. • When Smart Hub is launched for the first time, the default apps are automatically installed. The default apps may differ by region.
Page 54
You cannot play media content if the content or the storage device is not supported by the TV. For more information, refer to "Read Before Playing Photo, Video, or Music Files." • Backup important files before connecting a USB device. Samsung is not responsible for damaged or lost files. 2-15...
Page 55
2. Product specifications NewsON NOTE • Screen images may differ by model. • Before you use the NewsON Service, check if the TV is connected to the Internet. • The image may differ with the model. • This service or some of functions is not available on all countries or region. You can find daily information on a wide variety of topics in a smart and convenient way, updated in real time.
2. Product specifications 2-4-3. Using the web browser You can surf the Internet on the TV in the same manner as you would using a PC - even while watching a TV programme using PIP. Select Help to view the information of the Internet web browser. NOTE •...
Custom to turn on or off the sound from the selected screen. If you connect a Bluetooth headphone, you can only select Bluetooth Headphones. NOTE On the Samsung Smart Control, press the MENU/123 button, and then select Speaker List to set the speaker of each screen. 2-18...
NOTE • When Samsung Instant On is set to On, the use history of the apps that you used on the TV may be stored in the • The Samsung Instant On function works when you turn on the TV while its power cable is still connected after you set Samsung Instant On to On.
2. Product specifications 2-4-6. HDMI UHD Color Allows you to set the HDMI UHD Color mode to On or Off for each HDMI connector on the TV. When set to On, the TV optimizes processing of UHD 50P/60P signals. To configure the HDMI UHD Color mode for each HDMI connector, turn off the external devices. You can leave the HDMI cables connected to the TV.
Page 63
2. Product specifications Other Restrictions • Codecs may not function properly if there is a problem with the content. • Video content does not play or does not play correctly if there is an error in the content or container. •...
3. Disassembly and Reassemble 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LED TV. This LED TV contains electrostatically sensitive devices. Use caution when handling these components. WARNING 3-1. Disassembly and Reassembly Disconnect the LED TV from the power source before disassembly.
Page 65
3. Disassembly and Reassemble Description Picture Description Screws Remove the ASSY COVER P-REAR. Remove the Electric tapes shown on the Filament Tape: EMI Point image. • EMI Point : After removing release paper from the LVDS Cable bottom, attach the LVDS Cable to the C/ Filament Tape: Dressing Point Chassis and rub the attatched surface.
Page 66
3. Disassembly and Reassemble Description Picture Description Screws Remove the NETWORK (BT/WIFI COMBO) Cable. NETWORK (BT/WIFI COMBO) Cable Remove the screws of ASSY PCB MAIN Torque : and DC VSS-LED TV PD BD. 7~ 8Kgf.cm. • ASSY PCB MAIN : 4 EA •...
Page 67
3. Disassembly and Reassemble Description Picture Description Screws Remove the IR unit. • Remove the IR unit by moving it from up to down. IR Assy Remove the JOG unit. • Remove the JOG unit by moving it from bottom to top. Completed disassembly.
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting 4-1-1. Previous Check Check the various cable connections first. Check to see if there is a burnt or damaged cable. Check to see if there is a disconnected or loose cable connection. Check to see if the cables are connected according to the connection diagram. Check the power input to the Main Board.
Page 69
4. Troubleshooting 55 inch Bluetooth/WIFI Combo Module Power Board Main Board Power Cable Panel Connectors LVDS Cable T-CON Board Jog Function Speaker IR Sensor 60 inch Bluetooth/WIFI Combo Module Power Board Main Board Panel Connectors Power Cable LVDS Cable T-CON Board Jog Function Speaker IR Sensor...
4. Troubleshooting 4-2. How to Check Fault Symptom 4-2-1. Video Customer Picture Test Main Board Pre FRC Post FRC Problem Pass Pass Pass Check Signal Source and other inputs Fail Pass Pass Main Board or LVDS Cable Fail Fail Pass FRC (Main Board in TV) Fail...
Page 71
4. Troubleshooting Troubleshooting Video Test Power TV ON. Verify initial Start Up Screens with Power On. Press Mute 147 Mute to view Test Pattern from the MAIN Board. Press Mute 369 Mute to view Test Pattern from T-CON Board. Start Up Screens Mute 147 Mute Mute 369 Mute MAIN Board...
4. Troubleshooting 4-2-2. Bluetooth / WIFI Module Bluetooth Module Troubleshooting Check Bluetooth Address at Contact Samsung. BT Address Check BT Version at Factory Mode screen. Might require upgrade. Check GSPN. T-HKMAKUC-XXXX.XX T-HKMAKUS-XXXX BT Version BT Version : BLUETOOTH-VER-XXXX E-MANUAL : HMUATSCJ-X.XXX...
Page 73
4. Troubleshooting WIFI Module Troubleshooting Check Wired MAC Address and Wireless MAC Address at Contact Samsung. Wired MAC Address Wireless MAC Address Check Wired MAC and Wireless MAC at Factory Mode screen. (Success/Failure) Wired MAC errors : Main Board is defective.
Page 74
4. Troubleshooting BT/WIFI Combo Pin Map BT modul Wi-Fi modul Pin # Signal Description BT_Reset BT Block Reset Power DET Power detect(Active Low) BT_Wake up BT Wake up USB DM BT USB interface USB DP BT USB interface Ground 3D_sync_in 3D sync input 3D_sync_out...
Page 75
4. Troubleshooting 15' BT / WIFI Combo • Waveforms of combo Module Pins (3.3V except VCC 5V) Stand by On state BT nReset BT Power_det BT wake up High BT USB DP & DM Don't care 60HZ signal swing (3D mode only) 3D sync in &...
4. Troubleshooting 4-2-3. Jog Function Control Jog Function Control Press Left Right Down Center Vol+ Vol- Jog Function Control Test Check Jog Shuttle STBY Voltages (All at 1.8VDC except LED) Check Jog Shuttle 5 SW Operation Key1 & Key 2 for each command change. (See Chart) Check LED active during STBY (1.8VDC ) Signal DC Voltage...
4. Troubleshooting 4-2-4. T-CON Board T-CON Operation and Testing Test for 12VDC at both sides of Fuses on the TCON Board. If no 12VDC on either side of fuses, check 12V feed from the LVDS Cables & Main Board. If 12VDC only on one side of fuses replace defective TCON Board. Inspect LVDS and Panel Cable Connectors.
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1. Detail Factory Option NOTE If you replace the main board with new one, please change the factory option as well. The options you must change are "Type". UN**JS7000FXZA Inches 50" 55" 60" Vendor SHARP PANEL...
4. Troubleshooting 4-3-2. Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : • If you do not have Factory remote control Power OFF MUTE Power On • If you have Factory remote control INFO Factory •...
4. Troubleshooting 4-3-3. Factory Data Option Factory Menu Name Data Range Factory Reset Type 50D6AU0TJ 55B6AU0TJ, 55A6AU0TJ 60H6AU0TJ Local Set SW Model UJS6900 BOM Model 7000 TUNER S_TDA18275A Ch Table NONE MRT Option Front Color Engineer Option Control Factory Menu Name Data Range...
Page 81
4. Troubleshooting Factory Menu Name Data Range TTX Group UserOSD Visual Test Disable OPTION_SWU RF Remocon Support CDD mode … DPMS Support T-CON Device Status OK LMN 1ST THRESHOLD LMN 2ND THRESHOLD LMN 3RD THRESHOLD EOS Click BP PMS Reset FAnet Thread User InstantOn Default Value CI CPLD Version...
Page 82
4. Troubleshooting Factory Menu Name Data Range Peak Mode Metadata Asia Option Unbalance AF Level adjust TX Power Level Mono Last Memory H Shaking SOUND High Devi Carrier_Mute *If the broadcast signal is not good, TV will complement the characteristics of the signal (most use when weak signal comes from the growing area countries) Pilot Level High Thld...
Page 83
4. Troubleshooting Factory Menu Name Data Range Mic Scale India Sound Speaker Delay Normal NTV CU Delay Lipsync Inx Lipsync CheckSum 0x644C Lipsync USB Test Ready Lipsync BT CheckSum 0x0000 TP Volume 0xc9h TP Scale 0x64h TP EQ CheckSum NONE Debug ...
Page 84
4. Troubleshooting Factory Menu Name Data Range Stress Mode Log Analyzer Error Popup On/Off Deadlock KILL CES Mode ON/Off NONE CES Option CES Convergence Option TCON Demura Bypass BT DUT Reproduce Module 21_9 Factory Menu Name Data Range Self Test(for HW) Info Upgrade T-CON Usb Download...
Page 85
4. Troubleshooting Factory Menu Name Data Range IR Blaster Upgrade Failure IR Blaster delay time NTV CU Update Failure UD LDC PROFILE UPGRADE Failure Pic Data USB Update P:071/M:002 Audio Data USB Update Eco Data USB Update E:081/M:002 CI CPLD Upgrade Failure TCON DEMURA FW UPGRADE Reset...
Page 86
4. Troubleshooting Factory Menu Name Data Range HDCP UPDATE SPI READY * Upgarde HDCP SPI(There is upgrade program in Main-Image) SPI VERSION 0000XXXX HdmiRx EQ DVB CI European specifications Test Pattern * the Output of test pattern from each IC Other setting SVC Panel ORIGINAL...
Page 87
4. Troubleshooting Factory Menu Name Data Range B-Gain WB-W2_R_Offset WB_W2_B_Offset WB_W2_R_Gain WB_W2_B_Gain WB_N_R_Offset WB_N_B_Offset WB_N_R_Gain WB_N_B_Gain MGA On/Off R1_Gain G1_Gain B1_Gain R2_Gain G2_Gain B2_Gain R3_Gain G3_Gain B3_Gain R4_Gain G4_Gain B4_Gain R5_Gain G5_Gain B5_Gain R6_Gain G6_Gain B6_Gain R7_Gain G7_Gain B7_Gain R8_Gain G8_Gain B8_Gain R9_Gain...
Page 88
4. Troubleshooting Factory Menu Name Data Range B9_Gain R10_Gain G10_Gain B10_Gain SPI White Balance SPI MGA WB Data to SPI Advanced 4-21...
Page 89
4. Troubleshooting 4-4. White Balance 4-4-1. Calibration Into the Factory Mode. Select ADC/WB menu. Select menu. AV Calibration Option Comp Calibration Control PC Calibration Debug HDMI Calibration ADC/WB Advanced 4-4-2. Service Adjustment You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration ...
Page 90
4. Troubleshooting Method of Color Calibration (AV) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port. Press the Source key to switch to “AV1” mode. Enter Service mode. Select the “ADC” menu. Select the “AV Calibration” menu. In “AV Calibration Off”...
Page 91
4. Troubleshooting 4-4-3. Adjustment Into the Factory Mode. Select ADC/WB menu. White Balance Select menu. Option Control Debug (Low Light) (Hight Light) Sub Brightness Sub Contrast White Balance ADC/WB R offset R gain Advanced G offset G gain B offset B gain 4-24...
Page 92
4. Troubleshooting 4-5. RS-232C • RS232C Control Port : COM#(Serial) Baud rate : 9600 Data Bit : 8 bit Parity : None Stop Bits : 1 Flow Control : None • Description of RS232C Pin# Name Full Name Pin# Name Full Name Pin# Name Full Name...
Page 93
4. Troubleshooting 4-6. AV Control Tabe Control Item Cmd1 Cmd2 Cmd3 Value General Power Power 0x00 0x00 0x00 0x00 0x01 0x02 Volume Direct 0x01 0x00 0x00 (0~100) 0x01 0x00 Down 0x02 0x00 Mute 0x02 0x00 0x00 0x00 Direct 0x04 Continuous 0x01 0x00 0x03...
Page 94
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Mode Natural 0x03 CAL-NIGHT 0x04 CAL-DAY 0x05 BD Wise 0x06 Relax New function of 12" 0x07 (only PDP TV) BackLight 0~20 0x01 0x00 (0~20) (CellLight) Contrast 0~100 0x02 0x00 (0~100) Brightness 0~100 0x03 0x00...
Page 95
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Advanced Edge Enhancement 0x0f 0x00 Settings 0x01 xvYCC 0x10 0x00 0x01 Motion Lighting 0x11 0x00 0x01 Color Space Custom 0x12 0x00 Color Green 0x01 Blue 0x02 Only for active Color Space Custom Yellow 0x03 Cyan...
Page 96
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE Picture HDMI Black Level Normal 0x04 0x00 Option 0x01 Film Mode 0x05 0x00 Auto1 0x01 Auto2 0x02 Cinema New function of 12" 0x03 Smooth (only PDP TV) Auto Motion Plus 0x06 0x00 Clear 0x01...
Page 97
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value PICTURE 3D View Point 0x02 (-5~5) Depth 0x03 (1~10) 3D Auto View 0x05 0x00 Message 0x01 Notice 0x02 Control Item Cmd1 Cmd2 Cmd3 Value Sound Sound Mode Standard 0x0c 0x00 0x00 0x00 Music 0x01 Movie...
Page 98
4. Troubleshooting Control Item Cmd1 Cmd2 Cmd3 Value Sound Auto Volume Night 0x02 Speaker TV Speaker 0x07 0x00 0x00 Select External Speaker 0x01 Sound Main 0x08 0x00 0x00 Select 0x01 Sound Sound Reset 0x09 0x00 0x00 Reset 3D Audio 0x0a 0x00 0x00 0x01...
Page 99
4. Troubleshooting 4-7. Updating the TV’s Software • MENU/123 > MENU > Support > Software Update You can view your TV’s software version and update it if necessary. Updating the TV’s software to the latest version • MENU/123 > MENU >...
Page 105
5. Wiring Diagram SMPS Board <50 / 55 inch> CNL802 CNM803 AC Line Fuse & Power Connector <60 inch> CNM803 CNL802 AC Line Fuse & Power Connector...