Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BWT CBE 650
Summary of Contents for BWT CBE 650
- Page 1 CBE 650 Transversal bar pool safety cover designed to deny children under five access to the pool NF P 90-308 INSTALLATION AND OPERATING INSTRUCTIONS (to be read carefully and kept for future reference) 17/32 PROTECTION & SÉCURITÉ 2019/06 - Indice de révision : A - Code : 33905...
- Page 3 IMPORTANT - THIS COVER IS NO SUBSTITUTE FOR COMMON SENSE OR INDIVIDUAL RESPONSIBILITY, NOR IS IT INTENDED TO SUBSTITUTE THE VIGILANCE OF PARENTS AND/OR RESPONSIBLE ADULTS WHICH REMAINS THE KEY FACTOR IN ENSURING THE SAFETY OF YOUNG CHILDREN. - CAUTION: SAFETY IS ONLY ASSURED WHEN THE COVER IS CLOSED, LOCKED AND CORRECTLY INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.
-
Page 4: Table Of Contents
1. COVER FASTENING SYSTEM ..............20 2. INSTALLING THE COVER ................22 Pools featuring roman steps or straight steps at the end of the pool ......24 3. USING THE COVER ..................25 Rolling up the cover ......................25 Unrolling the cover .......................27 4. -
Page 5: Cover Fastening System
Tensioning strap Tension the end bars Cable tensioning strap components: - 1 Black strap with ring and Superlock buckle / CBE 650 6309010 - 1 dumbell shaped bar code 6409033 End plug To seal the bars 2 per par, except for the roll bar... - Page 6 • Use the profile replacing the coping as a template to drill two holes (Ø10 mm) in the coping at each end. Attach the profile to the coping by inserting a retaining staple at either end as illustrated. • On the deck, mark the position of the 3 pegs with •...
-
Page 7: Installing The Cover
INSTALLING THE COVER CONDITIONS PREREQUISITE TO INSTALLATION: • The area 100 cm around the pool must be cleared. • Paving must be firmly fixed to the ground and laid on a concrete apron with a cement content of 350 kg/m IMPORTANT: During installation, and regularly during use, check that the pads protecting the coping are correctly positioned, that is underneath the bars where they are in contact with the coping. - Page 8 Cover Storage side pool axis • On the deck, mark the position of the first 3 pegs • Drill holes for the Ø 8 mm pegs with bushing: with bushing according to the diagram above. Dimensions indicated are measured from inside - Use a Ø...
-
Page 9: Pools Featuring Roman Steps Or Straight Steps At The End Of The Pool
Pools featuring roman steps or straight steps at the end of the pool Cover pool axis Slide the stair extension with respect to the cover until it is perfectly positioned. FOLLOW THE DIAGRAM ILLUSTRATED ABOVE FOR POOLS FEATURING STRAIGHT STEPS OR ROMAN STEPS : A = peg position for attachment of bar tension straps. -
Page 10: Using The Cover
USING THE COVER Always keep an eye on the pool when opening and closing the cover. Rolling up the cover FOLLOW THESE STEPS: Position the strap used to unroll the cover: bring the long central strap down the middle of the pool to the “storage”... - Page 11 Unrolling strap - Removable section First bar of the 3-way buckle CBE 650 cover Quick disconnect fastener - Unrolling strap - Fixed section Female half Quick disconnect fastener - Male half Insert the crank.
-
Page 12: Unrolling The Cover
The cover should be rolled up slowly and as evenly as possible. Particular attention should be paid when rolling the bars, if the cover is allowed to fall sharply against the coping, the fabric could, due to the weight of the cover, suffer permanent damage at the points where it is caught between the bar and the coping. - Page 13 Attach and tension the tensioning straps. NOTE: Daily manipulation of the CBE 650 cover (rolling up - unrolling) entails multiple repeated contacts both between the various elements of the cover and with the ground. Dust, detritus, even sand or gravel can accumulate on the cover, adding to the friction.
-
Page 14: Maintenance
COVERNET detergent (Code 8880505): spread the detergent on the cover and brush lightly with a nonabrasive soft bristle brush. Allow it to act for 2 minutes and rinse with water. The CBE 650 cover must be cleaned regularly, at least twice a year. (At the beginning and end of winterizing). PROTECTION FROM THE WEATHER... -
Page 15: Winterizing
WINTERIZING Winterizing While wintering it is absolutely vital that the water level be maintained at least 2/3 of the way up the skimmer. To ensure that this criterion is met, we recommend that you consult with a professional. Empty water lines by blowing them with compressed air, plug water returns and insert gizmos into the skimmers. During the winter period: •... -
Page 16: Guarantee Conditions
Stitching Stitching Stitching Superlock buckle, black Triangular ring, diam 5 x 25 Strap DESIGNATION Tensioning strap routing GUARANTEE CONDITIONS The cover fabric is protected by a 2 year guarantee that covers the integrity of the welded seams and the cover fabric’s ability to withstand exposure to UV light The aluminium bars are covered by a two year guarantee against corrosion and degradation of the finishing lacque. - Page 17 3 566837 145071 32/32 2019/06 - Indice de révision : A - Code : 33905 PROTECTION & SÉCURITÉ...
Need help?
Do you have a question about the CBE 650 and is the answer not in the manual?
Questions and answers