Brookstone Big Blue - True Wireless Earbuds Manual
  1. Manuals
  2. Brands
  3. Brookstone Manuals
  4. Headphone
  5. BIG BLUE STUDIO
  6. User manual

Brookstone Big Blue - True Wireless Earbuds Manual

Also See for Big Blue:

Advertisement

Table of Contents
Contents
Brookstone Big Blue - True Wireless Earbuds Manual

Safety information

  • Listening to audio at a high volume may affect your hearing.
  • For adult use only.
  • Prolonged use may cause discomfort. If you experience discomfort, remove the earbuds
  • Do not drop, crush, bend or apply excessive force to the device.
  • Do not expose the device to moisture, extreme or prolonged heat, cold, humidity, or other adverse conditions. Avoid storage in damp, humid or wet locations.
  • The unit can only be opened by qualified personnel.

LITHIUM-ION BATTERY WARNING
This device contains a rechargeable Lithium-Ion battery. The battery must be recycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal. Use only the supplied cable to recharge the battery. Improper charging may damage the battery and the device.
Do not attempt to open the rechargeable battery or battery pack. There are no serviceable parts inside. Keep the battery out of reach of children. If swallowed, consult a physician immediately.
Do not dispose of battery in a fire as it may explode.
Battery may also explode if damaged.

LOCATION OF PARTS AND CONTROLS

LOCATION OF PARTS AND CONTROLS - Part 1

  1. Charging Contact Points
  2. Microphone
  3. LED Indicator
  4. Multi-Function Button

LOCATION OF PARTS AND CONTROLS - Part 2

  1. Charging Pins
  2. Earbud Charging Indicator
  3. Micro-USB Port
  4. Case Charging Indicator
  5. Earbud Charging Button

CHARGING THE CASE AND EARBUDS

Charge the case and earbuds before first use. If not used for a long period of time, they may require recharging.
To charge the case:

  1. Plug the charging cable's USB connector into a USB port on an active device, such as a laptop or USB adapter.
  2. Plug the charging cable's Micro USB connector into the Micro-USB port on the case. The Case Charging Indicator turns red during charging. The indicator turns off when the case is fully charged.
  3. When charging is complete, unplug the charging cable.

You can charge the earbuds while the case is charging or after the case is charged.
To charge the earbuds:

  1. Place the earbuds into the charging case. When properly inserted, the charging pins align with the charging contact points.
  2. Place the magnetic cover on the case.
  3. Press the Earbud Charging Button on the bottom of the case. The blue Earbud Charging Indicator turns on. The earbuds' LED Indicators are red while charging. They turn blue when fully charged.
  4. When charging is complete, press the Earbud Charging Button to end charging. The blue Earbud Charging Indicator turns off.

PAIRING WITH BLUETOOTH®

You can pair one or both earbuds with your Bluetooth® device. If pairing both, the earbud that is turned on first will be the main earbud; the second will be the auxilliary earbud.

  1. Prepare your device (e.g., smartphone) to pair using Bluetooth ®, making sure that the device is within 3 feet (1 meter) of the earbuds. Refer to your device's owner's manual for information on using the Bluetooth ® function.
  2. With the earbuds powered off, press and hold the Multi-Function Button of one earbud until the LED Indicator quick flashes blue and red alternately, indicating that the earbud is in pairing mode. Optionally, turn on the second earbud; its LED Indicator will flash blue when it is paired with the main earbud.
  3. On your device, search the list of available pairing devices and select BBlue Bead Buds. Note that it may take a few seconds for the earbuds to be listed as an available device. Depending on your device, you may have to tap SCAN to update the device list. Consult your device's owner's manual. If the connection is not made within 120 seconds, pairing mode is cancelled.
  4. If prompted, type the password or PIN 0000.
  5. The earbud's LED Indicator will flash blue, indicating that it is paried with the device.

The earbuds will remain paired with your device, even after being turned off, until you cancel the pairing. Consult your device's owner's manual for information on cancelling pairing.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Brookstone is under license.
Big Blue® is a registered trademark owned by Big Blue Audio LLC.

OPERATION

Perform the following on one or both earbuds. Ensure that the earbuds are within 3 feet (1 meter) of your device.

Function Multi-Function Key
Power on Long press until the LED Indicator flashes red, then blinks blue when reconnected with your mobile phone. Ensure that your device is within 3 feet (1 meter) of the earbuds.
Ensure that Bluetooth is enabled on your device and it has been paired with the earbuds. Tap BBlue Bead Buds in your device's Bluetooth list if necessary to reconnect.
Depending on whether you paired one or both earbuds, one earbud may be the main earbud and must be powered on for the auxiliary earbud to play.
Power off Long press until the LED Indicator blinks red once then turns off.
Play/pause Short press.
Next track Press twice.
Answer a call Short press when there is an incoming call. Caller ID is available. Call quality is enhanced with CVC6.0 noise cancellation technology.
End a call Short press while in a call.
Reject a call Press twice when there is an incoming call.

NOTE: Your device's app settings may prohibit control of some apps by the earbuds.

POSITIONING THE EARBUDS

  1. Insert the earbud into the outer ear.
    POSITIONING THE EARBUDS
  2. Rotate the earbud to gently insert it into the ear.

TROUBLESHOOTING

Bluetooth® pairing is unsuccessful

Check that the earbuds are in pairing mode (red and blue flashing), that the device's Bluetooth mode is enabled, and that the device is within 3 feet (1 meter) of the earbuds.

The earbuds are not paired with each other

Turn off both earbuds, then turn them both on at the same time by long pressing the Multi-Funciton Button for more than 8 seconds. The LED indicators will flash red and blue, then will flash blue when the earbuds are paired with each other. Pair with your Bluetooth® device.

The earbuds do not turn on

Check that the battery is not depleted.

The earbuds disconnect from the device

Ensure that no objects are interfering with the connection. Ensure that the earbuds are within 33 feet (10 meters) of your device.

There is no sound

Check the volume on your device and check that Bluetooth® is enabled and supports the A2DP profile.

CARE AND MAINTENANCE

Clean the earbuds with a soft cloth or damp chamois leather. Never use solvents.

SPECIFICATIONS

Dimensions, Case Approx. 1.8 x 1.3 x 1.4 in.
(46 x 34 x 35 mm)
Dimensions, Earbuds Approx. 0.9 x 0.8 x 0.5 in.
(24 x 20 x 13 mm)
Weight, Earbuds Approx. .28 oz (8g)
Weight, Earbuds and Case Approx. .88 oz (25 g)
Bluetooth Version Compatibility 4.2
Bluetooth Transmission Range Up to 33 ft (10 m)
Battery 260mAh Lithium -Ion
Battery Capacity 50mAh (earbud)
300mAh (charging case)
Battery Life Up to 2.5 hours (both earbuds)
Up to 5 hours (one earbud)
Standby Time Up to 60 hours (both earbuds)
Up to 120 hours (one earbud)
Charging Time, Case Approx. 2 hours
Charging Time, Both Earbuds Approx. 1 to 2 hours

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Brookstone Big Blue - True Wireless Earbuds Manual

Advertisement

Need Assistance?

Do you have a question about the Big Blue that isn't answered in the manual? Leave your question here.

Error while submitting your question. Please, reload page and try again.

Thank you! Your question has been received!

Related Manuals for Brookstone Big Blue

Save Article as PDF

Table of Contents