Bosch UniversalCut 18V-65 Original Instructions Manual page 14

14 | English
All-purpose saw
Recommended battery char-
C)
gers
A) Depends on battery in use
B) Limited performance at temperatures < 0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
94 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑11:
Cutting boards with saw blade NanoBlade Wood Speed 65:
2 2
a = 2.5 m/s , K = 1.5 m/s .
h,B
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
1 609 92A 8MP | (06.03.2023)
charge the rechargeable battery before using your tool for
UniversalCut 18V‑65
the first time.
AL 18...
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
Battery charge indicator
The battery charge indicator indicates the remaining battery
capacity or an overload when the power tool is switched on.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × slowly flashing green light
The three LEDs in the battery charge indicator flash quickly
when the temperature of the rechargeable battery is outside
the operating temperature range and/or the overload protec-
tion has been triggered.
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Avoid contact with the skin when changing a saw
u
blade and use protective gloves in perfect condition.
The saw blade can become hot when in operation for a
long time.
Do not pull on the chain and do not pull the chain off
u
the guide unit.
Always replace a complete saw blade with another complete
saw blade. The chain cannot be replaced on its own.
Capacity
75–100 %
40–75 %
15–40 %
0–15 %
Bosch Power Tools