SOMFY 1860326 Quick Start Manual

SETUP
GATEWAY MUST BE INSTALLED BY A QUALIFIED TECHNICIAN.
(CHECK WITH LOCAL AND NATIONAL CODES FOR PROPER INSTALLATION)
CAUTION — Observe precautions for handling
1
electrostatic sensitive gateways.
WARNING — Risk of Electric Shock. Do not handle
2
energized gateway with wet hands or when standing
on wet or damp surfaces.
WARRANTY — voided if gateway has been modified
3
from its original configuration.
Do not use outdoors.
4
Use only with Class 2 Power Unit – 60VDC maximum.
5
Conforms to UL1310 standard – Certified to CSA
6
standard C22.2 NO. 223.
7
Mounting pattern is shown below.
FIGURE 1. CONNECTION INFORMATION

CONNECTIONS AND INDICATORS

This device could be used in other configurations than
listed below. For specification information on individual
products, see related product information. Follow all
SDN wiring standards for distance limitations.
Notes:
• Control up to 4 low-voltage RS485 motors from
a SDN PoE Gateway.
• When operating motors as a group, motors will
cascade individually.
• Aligned operation available with
Sonesse® 30 RS485 DC (maximum 2 motors)
• Total wiring between SDN PoE Gateway and all
motors should not exceed 240 ft. when using
Liberty AV 9020126 cable.
• Total wiring between Network switch and SDN PoE Gateway
should not exceed 300 ft. using Category 5e cable.
SDN Power over Ethernet
Part Number: 1860326
NOTE: Ref. # 1870445 includes the SDN Power over Ethernet (PoE) Gateway and PoE Gateway to Motor Adapter Cable (9025010) sold as a kit.
The SDN Power over Ethernet (PoE) Gateway is a low-voltage power distribution and network-connected module that utilizes
PoE (Power over Ethernet) technology to power and control the Somfy® 24V RS485 motorization offer for shades and draperies.
Mounting Hole Location
Holes For Stand-alone
Metal Gateway
ELEMENT
1 Ethernet Input
2 SDN Output to motors
LED Indicators
LABEL
PWR
ACT
LINK

Installation Guide for PoE Gateway

Installation Guide for PoE Gateway
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Mounting pattern is shown below.
Mounting pattern is shown below.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Mounting Hole Location Holes For 180852
Mounting Hole Location Holes For 180852
Standalone Metal Gateway
Snap in the wire harness male connector into the female connector as shown below:
Snap in the wire harness male connector into the female connector as shown below:
8
Snap in the wire harness male connector into the female connector as shown below:
9 Use two #8 self-tapping screws to mount the PoE Gateway as shown
Use two #8 self-tapping screws to mount the PoE Gateway as shown
(screws not provided)
(screws not provided).
On the front top side of the PoE Gateway connect PoE CAT cable until you hear a
Use two #8 self-tapping screws to mount the PoE Gateway as shown
10 All motors and wiring need to be connected to Gateway prior to powering
"CLICK". Use a UTP
(unshielded twisted pair)
(screws not provided).
the SDN PoE Gateway
of cable should not exceed 100 meters.
On the front top side of the PoE Gateway connect PoE CAT cable until you hear a
11
On the front top side of the PoE Gateway connect PoE CAT cable until you hear a
"CLICK". Use a UTP
(unshielded twisted pair)
"CLICK". Use a UTP
(unshielded twisted pair)
of cable should not exceed 100 meters.
length of cable should not exceed 100 meters.
*Please note the Power LED indicator will turn on once you have power. The LINK and ACTIVE indicators will blink on and off
rapidly once you have network connection.
*Please note the Power LED indicator will turn on once you have power. The LINK
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
*Please note the Power LED indicator will turn on once you have power. The LINK and ACTIVE indicators will blink on and off
!
rapidly once you have network connection.
and ACTIVE indicators will blink on and off rapidly once you have network connection.
Download and install Programming Software from this link.
12
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
https://www.somfysystems.com/support/tools/configuration-tools-software
FUNCTION
Power and Data Input
from PoE system
Power and Data output to Somfy
24V DC SDN RS485 motors
ELEMENT COLOR FUNCTION ON
Power Green Powered
Active
Ethernet
Green
Active
Ethernet
Communication
Linked
Orange
(blinks)
Link
(PoE) Gateway
Standalone Metal Gateway
CAT5E or CAT6 cable*. The maximum length
CAT5E or CAT6 cable*. The maximum length
CAT5E or CAT6 cable*. The maximum
1
FUNCTION OFF ACT
PWR
No Power
1
No Ethernet
Activity
Side view
Not Linked
LINK
(not blinking)
2
2
Side view