SOMFY SOLIRIS SMOOVE UNO Installation Guide

Safety and liability

Liability

Before installing and using this product, please read these instructions carefully. This Somfy product must be installed by a home drive and automation professional. Moreover, the installer must comply with standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. He must give them these instructions. Any use outside the sphere of application defined by Somfy is prohibited. This invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories.

Safety instructions

Keep out of reach of children.
Never drop, knock, drill or submerge.
Do not use abrasive products or solvents to clean it.

Product description

Soliris Smoove Uno is a timer that can automatically and manually control a roller shutter, awning or external venetian blind type motor. Soliris Smoove Uno is pre-set to open at 7:30 am from Monday to Friday and at 8:30 am at the weekend, and to close at 8:00 pm. Soliris Smoove Uno also enables applications to be controlled automatically in accordance with the brightness using an optional sunlight, wind or rain sensor. The product parameters can be modified from the backlit screen.

Description of the control buttons

(Figure A)

Arrow :

• Manual raising and lowering control in normal operation.
• Navigation or changing the value in the settings menu.

Brief press (less than 2 seconds):

• When moving: stop function
• When stationary: switch to position

Brief press (less than 2 seconds):

• Return to the upper part of the menu or to the main screen.
• On the main screen, the functions used are displayed.

• Brief press (less than 2 seconds) from the main screen: access to the quick menu.
• Press and hold down (longer than 2 seconds) from the main screen: direct access to the settings menu.
• Activation in the settings menu: confirms an entry.

After 3 minutes, the appliance will enter standby mode and the display will switch off. Stand-by mode ends once a key is activated.

Connection

(Figure B)

The installation, testing and commissioning of the appliance must be carried out by qualified personnel.
Switch off all the connecting cables. Ensure that they cannot be accidentally switched on.

Observe the wiring of Neutral and Live.
Keep the "up" wiring and "down" wiring in the right directions.
Refer to the sensor instructions for information about their connection.

Installation

Dimensions and parts

(Figure C)
Dimensions: see figure

1. Electronic module
2. Cover frame
3. Power supply module

Installation

(Figure D)

1. Connect up the connection cables and secure the power supply module in the flush mounted box.
2. Position the electronic module with its cover frame in the power supply module. Switch on the power supply.

Initial commissioning

(Figure E)

If the appliance has already been commissioned, the main screen displays (image ).
If the appliance is in its original configuration, carry out the settings , and step by step.
Each setting must be confirmed with the "ok" button in order to access the next step: language, time, date (dd/mm/yy), type of equipment, linear travel (*1) and using the sensors.
When setting is complete, the appliance operates and the main screen is displayed (image ).
(*1) The linear travel time is the time required for a roller shutter, an external venetian blind or an awning to move from the open position to the fully closed position.

Setting the travel in automatic mode:
To raise the product, select "Start". To stop it, select "Stop" as soon as the product is at the end of the upper end limit. Press the button .
To lower the product, select "Start". To stop it, select "Stop" as soon as the product reaches the lower end limit. Press the button .
The travel time is set.
All information on the basic settings are in the online manual.

The motor end limits must be set in advance.
Advice for operating the external venetian blind: if the product does not move or barely moves after jogging, adjust the maximum tilting time of the slats or the start-up delay time (see the online manual).

Quick menu

(Figure F)

On the main screen, briefly press the button . Several operating modes will appear:

1. Automatic mode: all the automatic functions are activated. Manual control is possible.
2. Automatic mode stand-by: the automatic functions are deactivated for 6, 12 or 18 hours. The automatic functions then automatically re-activate.
3. Holiday mode: a presence is simulated if the clock function with fixed times is activated (see online manual).
4. Manual mode: automatic mode is deactivated.
5. Settings: access to the settings menu (see the instructions).

Saving and deleting the favourite position

(Figure G)

Prerequisite: the travel time should be accurately set (see the commissioning section).

Saving the favourite position

Position the product in the required position and stop it by briefly pressing the button .
Press button again for at least 5 sec. The position is saved.

Deleting the favourite position

Position the product in position .
Press button for at least 5 sec.
The position has been deleted.

Restoring the original configuration

(Figure H)

1. Set the user profile in professional mode in "Configuration menu" / "Configuration" / "User mode set-up".
   Confirm the "Professional" option by pressing button .
2. In the "Configuration" sub-menu chose the "Service" option.
   Confirm "Factory reset".
   Press the down button and select "Yes". Confirm by pressing button .
   The basic settings must be carried out again.

Optional

(Figure I)

QuickCopy™ setting tool

Using this setting tool and the corresponding PC software (available free-of-charge to download), the settings can be configured very easily and transferred to other products. (See the QuickCopy™ instructions)

Sunis Wirefree io™ radio-controlled sunlight sensor

This sensor enables the twilight and sunlight functions to be used. (See the Sunis Wirefree io™ instructions)

Wired sensor (wind, rain, sunlight)

These sensors enable the wind, rain and sunlight functions to be used with the Soliris Smoove Uno (see the sensor instructions).

Technical data

Do not dispose of this product with the household waste. Please take it to a collection point or an approved centre to ensure it is recycled correctly.

Somfy SAS
50 avenue du Nouveau Monde
F - 74300 Cluses

www.somfy.com