Advertisement
opticlimate.com
II
BY OPTICLIMATE
INSTALLATION
PLEASE READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THE UNIT:
High Temperature Safeguard on page 7
& USER GUIDE
Delete alarm history on page 12
Dehumidify without cooling pro4 on page 12
Engineered & Designed in Holland
THE FUTURE OF COOLING
JUST GOT COOLER.
www.opticlimate.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for OPTICLIMATE ZEVOMAX II
Summary of Contents for OPTICLIMATE ZEVOMAX II
- Page 1 BY OPTICLIMATE INSTALLATION PLEASE READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THE UNIT: High Temperature Safeguard on page 7 & USER GUIDE Delete alarm history on page 12 Dehumidify without cooling pro4 on page 12 Engineered & Designed in Holland THE FUTURE OF COOLING JUST GOT COOLER.
-
Page 2: Installation
INSTALLATION INSTALLATION Stand or frame Make or buy a stand or frame to hold the weight of the Opticlimate. (see nameplate ) Installation You can use the rubber damper or a vibration damper (not incuded) Pinch a hole through the insulation at the position of the 4 holes in the bottom of the unit. Use an M8 bolt and washer to mount the rubber or damper. -
Page 3: Electrical Connection
The remote control contained in the compartment can be hung in the room but can also be hung elsewhere. This way the OptiClimate should be placed on the ground at the lowest point. The end of the sensor cable can also be controlled from outside the room. -
Page 4: Power Supply Specifications
LeGrand Grasslin The two ends should be connected to terminals 15 & 16 on the terminal strip in the electrical compartment of the OptiClimate. The OptiClimate supplies the power for the timer. The OptiClimate supplies the power for the timer. If the room temperature exceeds 35°C, the OptiClimate will interrupt the circuit, switching off the heat sources. - Page 5 The unit can be used by connecting the water in and out connections to a cold water supply and a drain or can be used using the Opticlimate water cooler to cool the water in a closed loop. (connections and discription of a water cooler setup need to be obtained in the water cooler manual.
- Page 6 After powering up the Opticlimate, the unit will first initialize, this can take a few minutes. All valves and sensor are tested prior to startup. The remote controller cannot be operated during initializing of the Opticlimate. After powering up the Smart remote controller, the remote will first initialize, this can take a few minutes. You will see several screens pop-up and close again, this is normal.
-
Page 7: Powering Up The Unit
POWERING UP THE UNIT OPERATING BY USING THE SMART REMOTE CONTROLLER After both Smart controller and Opticlimate are initialised, the Smart Remote controller will display the Home screen *1 Setting the basic parameters Alarm Go to home 1 or home 2 by pressing the home icon. - Page 8 OPERATING BY USING THE SMART REMOTE CONTROLLER OPERATING BY USING THE SMART REMOTE CONTROLLER Switching the unit on or off Setting day and night dehumidify setpoint Setting day and night temperature setpoint. Go to home 1 or home 2 by pressing the home icon. In the right upper corner you find the on/off button.
- Page 9 OPERATING BY USING THE SMART REMOTE CONTROLLER By touching the home button you can go to the advanced screen and you can see more parameters displayed and also a simple datalog window. The settings for temperature and humidity is the same as in the basic screen. Home - Advanced Screen By touching the home button you can go to the advanced screen and you can see more parameters displayed and...
- Page 10 BY OPTICLIMATE ® Opticlimate is a registered trademark of airSupplies INSTALLATION & USER GUIDE Engineered & Designed in Holland Manual version 01 13 2023 THE FUTURE OF COOLING JUST GOT COOLER. www.opticlimate.com...
Need help?
Do you have a question about the ZEVOMAX II and is the answer not in the manual?
Questions and answers