Subscribe to Our Youtube Channel
Related Manuals for Palmgren 9680149
Summary of Contents for Palmgren 9680149
- Page 1 Operating Manual & Parts List 9680149 18˝ Mill Drill with dro and power feed Read carefully and follow all safety rules and operating instructions before first use of this product. 9646739.01-0221...
-
Page 2: Know Your Tool
9680149 DESCRIPTION KNOW YOUR TOOL Palmgren 18" Mill Drill w/ DRO and Power Feed, Model 9680149 is for milling or drilling, widely used in different places. Fine exterior, wide range of speed and easy to use. Designed for industrial usage milling, drilling, reaming, steps and mill plane with metal and other material. -
Page 3: Safety Rules
Palmgren Operating Manual & Parts List 9680149 binding, breakage, mounting and any other condition that may SAFETY RULES affect a tool’s operation. • Damaged parts should be properly repaired or replaced. Do not WARNING: For your own safety, read operating instructions manual perform makeshift repairs. -
Page 4: Operation
(C), can make the perform normal operations. 9680149 comes with a stand, but can spindle speed raise to the highest position. Under these also be mounted to workbench. - Page 5 Palmgren Operating Manual & Parts List 9680149 OPERATION (CONTINUED) Figure 8 - Chuck guard with safety switch. Figure 5 – Spindle belt and gearing. Figure 9 - Spindle fine feeding ( tighten the lock knob “A” then turn the fine feeding knob “B” .
- Page 6 Palmgren Operating Manual & Parts List 9680149 OPERATION (CONTINUED) INTRODUCTION OF HIGH AND LOW SPEED SHIFT 1. Loosen and remove the hand screws and gaskets on the top cover of the box; Figure 16 – Unlocking screw. Figure 12 – Hand screw location.
- Page 7 Palmgren Operating Manual & Parts List 9680149 OPERATION (CONTINUED) BRIEF INTRODUCTION OF CONVENTIONAL MECHANICAL OPERATION 1. The clamping tool and work piece must stop the machine first; 2. Clean the inner hole of the spindle and the conical surface of the tool rod, push the tool rod into the inner hole of the spindle, and put in the pull rod to hang the tool rod;...
-
Page 8: Maintenance
Palmgren Operating Manual & Parts List 9680149 OPERATION (CONTINUED) Figure 30 – Lubrication locations. The main ones that need to be lubricated are XYZ's three axial thread Figure 27 – Spindle screw. rods and rod nuts. Figure 31 – Lubrication locations. - Page 9 Palmgren Operating Manual & Parts List XXXXX MAINTENANCE (CONTINUED) OBLIQUE PLUG IRON ADJUSTMENT This mill uses an oblique plug iron (angle degree is 1:100) between the base and saddle, saddle and work table, head stock and fuselage. Thie plug iron allows smooth high accuracy movement for each part.
-
Page 10: Electrical Schematic
Palmgren Operating Manual & Parts List 9680149 ELECTRICAL SCHEMATIC Figure 35 - Electrical Schematic... -
Page 11: Troubleshooting
Palmgren Operating Manual & Parts List 9680149 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Motor cannot start 1. The power supply is not on. 1. Turn on the emergency stop button 2. Low voltage 2. Check that the voltage of the power supply is correct. - Page 12 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 1D Figure 36 – Replacement Parts Illustration for Headstock with DRO...
- Page 13 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 2B Figure 37 – Replacement Parts Illustration for Column with Z Axis Motor Auto Lift...
- Page 14 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 3A Figure 38 – Replacement Parts Illustration for Magnetic Scales and Readers...
- Page 15 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 4A Figure 39 – Replacement Parts Illustration for Worktable and Base...
- Page 16 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 5B Figure 40 – Replacement Parts Illustration for Left Control Box with Z Axis Auto Lift Switches...
- Page 17 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 6A Figure 41 – Replacement Parts Illustration for Power Feeder Clutch Assembly...
- Page 18 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 6B Figure 42 – Replacement Parts Illustration for Power Feeder Limit Devices Assembly...
- Page 19 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS ILLUSTRATION 7A Figure 43 – Replacement Parts Illustration for Dustproof and Chuck Guard Assembly...
- Page 20 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS LIST FOR 18˝ MILL DRILL W/ DRO & POWER FEED Ref. Ref. Description Part No. Qty. Description Part No. Qty. 1D-1 JT6 taper shank 9646740.01 1D-52 Washer 1D-2 R8 spindle 9646741.01 1D-53 Handle 9646777.01...
- Page 21 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS LIST FOR 18˝ MILL DRILL W/ DRO & POWER FEED Ref. Ref. Description Part No. Qty. Description Part No. Qty. 2B-5 Internal thread taper pin 6*32 9646812.01 4A-18 Hexagonal locking nut M12...
- Page 22 Palmgren Operating Manual & Parts List 9680149 REPLACEMENT PARTS LIST FOR 18˝ MILL DRILL W/ DRO & POWER FEED Ref. Ref. Description Part No. Qty. Description Part No. Qty. 5B-19 Hexagonal isolation column HTS-310 9646884.01 6A-12 Shaft sleeve 9646919.01 5B-20 Upper liner 9646885.01...
- Page 23 Palmgren Operating Manual & Parts List 9680149 NOTES...
- Page 24 9680149 PALMGREN WARRANTY C.H. Hanson / Palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which is was intended.
Need help?
Do you have a question about the 9680149 and is the answer not in the manual?
Questions and answers