Subscribe to Our Youtube Channel
Related Manuals for Palmgren 80156
Summary of Contents for Palmgren 80156
- Page 1 & parts list 80155 and 80156 15″ HEAVY DUTY BENCH AND FLOOR MODEL DRILL PRESS Read carefully and follow all safety rules and operating instructions before first use of this product. 32111.09-0910...
- Page 2 80156 ........
- Page 3 Palmgren Operating Manual & Parts List 80155 and 80156 • Arsenic and chromium from chemically-treated lumber. • Avoid accidental start-up. Make sure switch is in OFF position before plugging in. Your risk from these exposures vary, depending on how often you •...
- Page 4 Palmgren Operating Manual & Parts List 80155 and 80156 MOUNT TABLE (80156) INSTALLATION Refer to Figure 7. • Attach crank handle (Ref. No. 22) to shaft of worm gear (Ref. No. Refer to Figures 2, 3 and 4. 20), rotate worm gear to remove slack, and shoulder crank han- dle with set screw (Ref.
- Page 5 Palmgren Operating Manual & Parts List 80155 and 80156 • A label on the motor describes the possible wiring configura- WARNING: This work should be performed by a qualified electrician. tions. There are many different possible combinations, so only A temporary 3-prong to 2-prong grounding adapter (See Figure 3) the diagram provided with the motor should be used.
- Page 6 Palmgren Operating Manual & Parts List 80155 and 80156 Belt Spindle Motor Location A1-5Z B2-5Z A1-4Y C3-5Z D4-5Z A1-3X B2-4Y A1-2W C3-4Y B2-3X 1491 E5-4Y 1660 D4-3X 1761 C3-2W 2362 D4-2W 2444 E5-3X Figure 5 – Spindle Speed Adjustment 3476...
- Page 7 Palmgren Operating Manual & Parts List 80155 and 80156 • Apply lubricant around the inside of the hole in the spindle MAINTENANCE pulley (Figure 8, Ref. No. 2). • Apply lubricant to rack (teeth) on quill (Figure 8, Ref. No. 24)
- Page 8 Palmgren Operating Manual & Parts List 80155 and 80156 TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Spindle does not turn 1. No power to drill press 1. Check wiring, fuse or circuit breaker 2. Defective switch 2. Replace switch 3. Defective motor 3.
- Page 9 Palmgren Operating Manual & Parts List 80155 and 80156 Service Record Palmgren 15″ Bench and Floor Model Drill Presses DATE MAINTENANCE PERFORMED REPLACEMENT PARTS REQUIRED...
- Page 10 Palmgren Operating Manual & Parts List 80155 and 80156 Figure 7 - Replacement Parts Illustration for Base...
- Page 11 Palmgren Operating Manual & Parts List 80155 and 80156 REPLACEMENT PARTS LIST FOR BASE Ref. Part Numbers for: Description 80155 80156 Qty. Base 32172.00 32177.00 8-1.25 x 125mm Hex head bolt 8mm Flat washer 8mm Lock washer 8-1.25mm Hex nut 10-1.5 x 40mm Socket head bolt...
- Page 12 Palmgren Operating Manual & Parts List 80155 and 80156 Figure 8 - Replacement Parts Illustration for Spindle and Drive...
- Page 13 Palmgren Operating Manual & Parts List 80155 and 80156 REPLACEMENT PARTS LIST FOR SPINDLE AND DRIVE Ref. Ref. Description Part No. Qty. Description Part No. Qty. Spindle nut 32126.00 JT3 chuck with key 32138.00 Spindle pulley 32127.00 Chuck key 32139.00 Spindle sleeve 32128.00...
- Page 14 Palmgren Operating Manual & Parts List 80155 and 80156 Figure 9 - Replacement Parts Illustration for Head...
- Page 15 Palmgren Operating Manual & Parts List 80155 and 80156 REPLACEMENT PARTS LIST FOR HEAD Ref. Ref. Description Part No. Qty. Description Part No. Qty. Knob assembly 32037.00 3-0.5 x 45mm Pan head screw Pulley housing 32183.00 6-1.0 x 12mm Tap screw 32252.00...
- Page 16 • Accessories – 1 year The obligation of Palmgren is limited solely to the repair or replacement, at our option, at its factory or authorized repair agent of any part that should prove deficient. Purchaser must lubricate and maintain the product under normal operating conditions at all times. Prior to oper- ation become familiar with product and the included materials, i.e.
Need help?
Do you have a question about the 80156 and is the answer not in the manual?
Questions and answers