Use And Maintenance - Cello Asteria 60 cm CPW583 Installation Instructions Manual

• In the case of assembly of the appliance in the suc-
tion version prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which
has the same diameter as the air exhaust outlet hole.
If a pipe with a smaller diameter is used, the efficien-
cy of the product may be reduced and its operation
may become noisier.
Fixing to the wall:
• Drill the holes A respecting the distances indicated (Fig.2).
• Fix the appliance to the wall and align it in horizontal
position to the wall units.
• When the appliance has been adjusted, definitely fix
the hood using the screws A (Fig.3).
• For the various installations use screws and screw
anchors suited to the type of wall (e.g. reinforced
concrete, plasterboard, etc.). If the screws and screw
anchors are provided with the product, check that
they are suitable for the type of wall on which the
hood is to be fixed.
Fixing the decorative telescopic flue:
• Plan and install the power supply according to the di-
mensions of the telescopic cover in the right place. At
the same time, plan the dimensioning of the exhaust
pipe for the right place and length.
• Adjust the width of the support bracket of the upper
flue (Fig.4).
• Then fix it to the ceiling using the screws A (Fig.4) in
such a way that it is in line with your hood and respect-
ing the distance from the ceiling indicated in Fig.2.
• Connect the flange C to the air exhaust hole using a
connection pipe (Fig.3).
• Insert the upper flue into the lower flue.
Installation as air returning indoors with an active
carbon filter:
Please note:
• In order to install the range hood as a model that re-
circulates the room air, order a device-specific active
carbon filter from your retailer. A suitable activated
carbon filter is (Cello 2009 ACF) Figure 5B

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on
before any food is cooked. We also recommend that
the appliance is left running for 15 minutes after the
food is cooked, in order to thoroughly eliminate all
contaminated air. The effective performance of the
cooker hood depends on constant maintenance; the
anti-grease filter and the active carbon filter both
require special attention.
• The anti-grease filter is responsible retaining the
grease particles suspended in the air, therefore it is
subject to clogging with variable frequency according
to the use of the appliance.
• To prevent the danger of possible fires, at least
every 2 months one must wash the anti-grease
filters by hand using non-abrasive neutral liquid
detergents or in the dishwasher at low tempera-
tures and on short cycles.
• After a few washes, colour alterations may occur. This
does not give the right to claim their replacement.
• The active carbon filters are used to purify the air
that is sent back into the room and its function is to
mitigate the unpleasant odours produced by cooking.
• The non-regenerable active carbon filters must
be replaced at least every 4 months. The satura-
tion of the active charcoal depends on the more
or less prolonged use of the appliance, on the
type of kitchen and on the frequency with which
anti-grease filter is cleaned.
• Before remounting the anti-grease filters it is import-
ant that they are completely dry.
• Clean the hood frequently, both internally and ex-
ternally, using a cloth dampened with neutral liquid
detergents that are non abrasive.
• The lighting system is designed for use during cooking.
• Attention: the non compliance with the hood cleaning
warnings and with the replacement and cleaning of
the filters entails risk of fires. One therefore recom-
mends keeping to the suggested instructions.
Replacing LED lamps (Fig.6B):
• The appliance is with LED lamps, the intervention
of a specialised technician is necessary to replace
them.
Control (Fig.7):
A Button = Switches the hood on/off. The equipment
switches on at the 1st speed.
B Button = Decreases motor speed.
C Display = Shows the selected motor speed and timer
activation/intense speed/filter warning.
D Button = Increases motor speed.
• Pressing the 4th speed button engages the intense
function for 6 minutes, then the equipment goes back
to working at the speed at which it was activated.
During this function, the number 4 flashes on the
display.
5