Page 1
User Manual VEGA-1000 HDMI 2.0 Transceiver Extender with Bi-Directional IR, RS-232, and Audio Extender/Extractor...
Page 2
The documentation and the software included with this product are copyrighted 2022 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. also reserves the right to improve the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
Page 3
This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
Page 4
Technical Support and Assistance Visit the Advantech website at http://support.advantech.com to obtain the latest product information. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before calling: –...
Page 5
In accordance with the IEC 704-1:1982 specifications, the sound pressure level at the operator’s position does not exceed 70 dB (A). DISCLAIMER: These instructions are provided according to IEC 704-1 standards. Advantech disclaims all responsibility for the accuracy of any statements contained herein. VEGA-1000 User Manual...
Page 6
Do not touch any components on the CPU card or other cards while the PC is powered on. Disconnect the power before making any configuration changes. A sudden rush of power after connecting a jumper or installing a card may damage sensitive electronic components. VEGA-1000 User Manual...
IR Earphone Jack ............... 10 HDMI Pin Definition................. 11 Figure 3.1 HDMI Type A (Receptacle)........11 Chapter Operation..........13 Software Control Via Ethernet..............14 4.1.1 System Requirements..............14 4.1.2 Software Control Program ............14 4.1.3 Control Interface ................. 14 VEGA-1000 User Manual...
Introduction VEGA-1000 is an HDMI 2.0 transceiver extender with bi-directional IR, RS-232, and audio extender/extractor that supports increased signal transmission distances of up 1, 2 to 100 m (330 ft) over copper or 300 m (990 ft) on OM3/400 m (1320 ft) on OM4 over fiber in ultra-HD 4K2K@60 (4:4:4) format.
Wall mount with screws Power Supply 12 V Power Consumption 12.5W max. Operating 0 ~ 40 °C (32 ~ 104 °F) Temperature Storage Temperature -20 ~ 60 °C (-4 ~ 140 °F) Relative Humidity 20 ~ 90% RH, no condensation VEGA-1000 User Manual...
ON (↓) ON (↓) Reserved Pin 1 Pin 2 OFF (↑) ON (↓) Reserved OFF (↑) OFF (↑) Reserved Set transmission mode to “over SFP” ON (↓) Pin 3 OFF (↑) Set transmission mode to “over copper” VEGA-1000 User Manual...
Page 16
LED Indicator: HDMI Out LED indicator LED Indicator: HDMI In LED indicator HDMI Out: for connecting an HDMI display using an HDMI male-male cable HDMI In: for connecting an HDMI input source using an HDMI male-male cable VEGA-1000 User Manual...
Should the cable need replacing, any IR extension cable that is compatible with the IR sockets can be used for the extender if necessary. However, IR cables that exceed 2 m (6 ft) in length may result in less than optimal function. VEGA-1000 User Manual...
(When selected, the device icons will be highlighted in yellow.) a. Type – VID – PID (15 over copper/16 over fiber) b. Output device ID (derived from the MAC address of the device) c. IP address d. Input device ID e. Firmware version VEGA-1000 User Manual...
Page 23
8 x 8 displays. The range can be set via the “Number” field. The wall dimensions can be defined by adjusting the orange frame on the left (as shown below), or by inputting specific parameters. After configuration, click “Preview” or “Apply” to implement the settings. VEGA-1000 User Manual...
Page 24
RS-232 routing. Select “send to all devices” to send text messages to all devices simultaneously. (Note: Set all devices to the same UART configuration before sending mass text messages.) VEGA-1000 User Manual...
Page 25
Users can select between HDMI Decoder EDID and Monitor EDID. After config- uration, click “Save EDID” to save the settings. Next, click “Upload EDID” to select the EDID file to upload for EDID learning. Users can also click “View” to check the EDID description. VEGA-1000 User Manual...
Page 26
IR commands to devices via infrared routing. Select “send to all devices” to send IR commands to all devices simultaneously. (Note: For more commands, search online for keywords related to infrared hex codes.) VEGA-1000 User Manual...
Page 27
Rename Select the target device and input a new Device ID in the “New ID” field. Click “Apply” to save the new device name. Alternatively, click “Reset” to reset the Device ID. VEGA-1000 User Manual...