Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Isolite Manuals
  4. Lighting Equipment
  5. ELT2.0 ELITE Series
  6. Installation and operating instruction

Isolite ELT2.0 ELITE Series Installation And Operating Instruction

Die cast aluminum led edge lit exit sign
Hide thumbs

Advertisement

Quick Links

Download this manual
ELT2.0 ELITE SERIES
DIE CAST ALUMINUM LED EDGE LIT EXIT SIGN
INSTALLATION AND OPERATING INSTRUCTION
Signs furnished with transparent backgrounds shall be installed only where there is adequate
color contrast between the sign legend and the interior wall finish behind the sign, to provide
for sufficient visibility.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including
the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use outdoors.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not readily be subject to
tampering by unauthorized personnel.
4. The user of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
5. Do not use this equipment for other than intended use.
6. Supply connections must be made either inside the junction box for surface mount or the splice
box in the recessed mount backbox.
7. Install using recommended junction box only.
8. Servicing of this equipment should be performed by qualified service personnel.
SAVE THESE INSTRUCTIONS
31 Waterloo Ave • Berwyn, Pa • 19312 U.S.A
Telephone: (610) 647-8200 • Email: support@isolite.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the ELT2.0 ELITE Series and is the answer not in the manual?

Questions and answers

Related Manuals for Isolite ELT2.0 ELITE Series

Summary of Contents for Isolite ELT2.0 ELITE Series

  • Page 1 7. Install using recommended junction box only. 8. Servicing of this equipment should be performed by qualified service personnel. SAVE THESE INSTRUCTIONS 31 Waterloo Ave • Berwyn, Pa • 19312 U.S.A Telephone: (610) 647-8200 • Email: support@isolite.com...
  • Page 2 Use the tool provided to remove any air bubbles [Figure 4]. FIGURE 1: Alignment Template FIGURE 2: Single Face Application FIGURE 3: Double Face or Clear / White / FIGURE 4: Removing Air Bubbles Using Mirror Background Single Face Tool Provided 2 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...

  • Page 3: Recessed Ceiling Mount

    Attach power plug into power receptacle assemble wired as per wiring instruction below. Insert second “wishbone” clip into remaining formed legs in backbox and push fixture flush with ceiling. FIGURE 6 FIGURE 7 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 4 SURFACE MOUNT (END, CEILING, BACK) END SURFACE MOUNT FIGURE 8: Surface End CEILING SURFACE MOUNT BACK SURFACE MOUNT FIGURE 9: Surface Ceiling FIGURE 10: Surface Back 4 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 5 Attach power plug to power receptacle and push back into fixture. Fasten fixture to spider plate with supplied countersunk screws. ATTACH THE GOOSE-NECK COVER Attach the goose-neck cover (surface end and surface back only) using the provided screws. PRODUCT KEY 1 SPIDER PLATE 2 CANOPY 3 GOOSE-NECK 4 GOOSE-NECK COVER ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 6 HANG-STRAIGHT PENDANT MOUNT ASSEMBLY FIGURE 11: Pendant Assembly 6 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 7 5. Connect wires according to local codes. 6. Attach canopy to the spider plate with the provided screws. PRODUCT KEY 1 SPIDER PLATE 2 CANOPY 3 UNIVERSAL JOINT 4 SADDLE 5 PENDANT STEM 6 PENDANT COUPLING 7 HOUSING ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 8 MOUNTING BRACKET ASSEMBLY FOR MULLION INSTALLATION FIGURE 12: Top Surface Mount FIGURE 13: Mounting Bracket Assembly 8 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 9 4. Connect and install the end mount assembly as per the instructions in this guide. 5. Replace the lens holder by snapping it into the housing. FIGURE 14 FIGURE 15 FIGURE 16 FIGURE 17: Surface End Assembly ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 10 LEDs for 5 minutes to check the lamp load and battery. The test will be performed only if the battery is fully charged. If not, the test will automatically reschedule. Charger function is monitored continuously. 10 ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...

  • Page 11: Status Indicators

    This product contains NiCd batteries. Used NiCd batteries may not be disposed of in the municipal solid waste stream. NiCd batteries must be recycled or disposed of properly. For information on local recycling drop-off points, phone toll free 1 -800-BATTERY (1-800-228-8379). ISOLITE    WWW.ISOLITE.COM Z410194  REV 2...
  • Page 12 SAVE THESE INSTRUCTIONS 31 Waterloo Ave • Berwyn, Pa • 19312 U.S.A Telephone: (610) 647-8200 • Email: support@isolite.com...