ZooZ ZEN53 LR User Manual

DC MOTOR CONTROLLER
www.getzooz.com
ask@getzooz.com
Manual or Z-Wave control of DC motors (reversed polarity)
Ÿ
Great for motorized shades, blinds, awnings, screens, and more
Ÿ
Shutter and Venetian blind modes to choose from
Ÿ
Installs behind your existing wall switch (momentary button)
Ÿ
700 series Z-Wave chip for better range and faster control
Ÿ
Z-Wave Long Range for ultra reliable no-mesh communication
Ÿ
Advanced configuration including timer settings and calibration
Ÿ
Built-in Z-Wave signal repeater for boosted communication
Ÿ
SmartStart and S2 Security for a safer network
Ÿ
Model Number: ZEN53 LR
Ÿ
Power: 6-32 VDC
Ÿ
Maximum Load: 1.5 A (use with DC motors only)
Ÿ
Range: Up to 300 feet line of sight (or up to a mile with LR)
Ÿ
Operating Temperature: 32-104° F (0-40° C)
Ÿ
Installation and Use: Indoor only
Ÿ
CAUTION
This is an electrical device - please use caution when installing and
operating the motor controller. Remote control of appliances may result
in unintentional or automated activation of power.
Do not use this Z-Wave device to control electric heaters or other
appliances which produce the risk of fire, burns, or electrical shock
when unattended.
To reduce risk of overheating and possible damage to other equipment,
do not install this unit to control a receptacle; a motor-operated
appliance; a fluorescent lighting fixture; any device over 32 V DC power;
or a transformer-supplied fixture.

BEFORE YOU INSTALL

This device is intended for installation in accordance with the
National Electric Code and local regulations. It is recommen-
ded that a licensed electrician perform this installation.
1. CHECK THE LOAD: don't exceed 1.5 A for your DC motor,
DO NOT CONNECT THIS DEVICE TO 120 VAC LOADS.
2. POWER OFF: turn the circuit power off in the breaker panel
before you start. If installing in a multi-switch box with
multiple circuits, turn power off at all of the circuits.
3. CHECK THE WIRES: mark motor connections (OUT), DC
power (GND- and VDC+), and switch connections (S1 and S2).
Don't rely exclusively on your multimeter to identify the
wires!
µ
NOT SURE WHAT YOU'RE SEEING? WE'LL HELP! SUPPORT.GETZOOZ.COM
SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
4. DISCONNECT THE SWITCH: remove the wires between the
switch and the motor and label them accordingly.
5. CONNECT THE MOTOR CONTROLLER: follow all
installation steps carefully. Wire the device EXACTLY like in the
diagram.

BUTTON SWITCHES ONLY

Do not connect the ZEN53 to a wall dimmer,
illuminated switches, or electronic add-on switches. The
ZEN53 device can only be wired with single pole button
momentary switches!
USER MANUAL
ZEN53 LR

FEATURES

SPECIFICATIONS

WIRING: READ IT!

PAGE 1

ZEN53 WIRING DIAGRAM FOR DC MOTORS

1 Connect the motor wires to OUT - and OUT + on ZEN53.
2 Keep your wall switch connected to the VDC positive +
on DC power. Connect S1 and S2 on the ZEN53 according
to the instructions for your wall switch. The diagram below
shows a single-pole double-throw center-off switch.
3 Connect the GND on the DC power source to the GND
pigtail on ZEN53.
4 Connect the VDC positive + on the DC power source to
the VDC+ pigtail on ZEN53.
Single-Pole Double
Throw Center-Off Switch

COMPLETE INSTALLATION

Secure your Z-Wave DC Motor Controller and the wall switch
in the box with mounting screws, handling the wires with
care. Install the wall plate and restore power to the circuit.

Z-WAVE CONTROL

1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web
interface). Check Long Range if using.
Not sure how? Scan one of the QR codes
below for step-by-step instructions or get in
touch: www.support.getzooz.com
2. Finalize inclusion at the device.
TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY
if using traditional Z-Wave inclusion.
SCAN THE QR CODE / ENTER THE 5-DIGIT PIN
if using the new SmartStart method.
The SmartStart security PIN is located on the back
of the relay, next to the Z-Wave Plus logo.
The LED indicator will blink green to signal communication
and turn green for 2 seconds if inclusion is successful or turn
red for 2 seconds if the pairing attempt fails.
NEED SOME HELP? ask@getzooz.com
Choose your hub and scan the QR code with your phone's
camera. Then click on the link to access the step-by-step
pairing instructions.
Z-Box Hub Hubitat
Get more tutorials and helpful tips at ww.support.getzooz.com
Register your product for extended warranty and
direct access to firmware files: getzooz.com/register
M
QUESTIONS?
ask@getzooz.com
S1
ZEN53
S2
OUT-
OUT+
GND-
VDC+
+
6-32 VDC
-

POWER SOURCE

SmartThings
Home Assistant
PAGE 2
LR