IMI norgren F64C Installation & Maintenance Instructions

Option selector
Option selector
Bowl/
Bowl/
Element
Element
C Standard
C Standard
H High flow
H High flow
Port
Port
Option selector 2 1/4"
2 1/4"
Thread
3 3/8"
3 3/8"
A (1/8 PTF gauge ports)
Bowl/
4 1/2"
4 1/2"
B (1/8 PTF gauge ports)
Element
6 3/4
6 3/4
G ISO G parallel (1/8 ISO Rc gauge
C Standard
ports)
H High flow
N No thread (basic unit)
Port
TECHNICAL FEATURES
Technical features
2 1/4"
Fluid: Compressed air
3 3/8"
Fluid: Compressed air
Maximum pressure:
4 1/2"
Maximum pressure:
6 3/4
Guarded transparent bowl: 10 bar (150 psig) Metal
Guarded transparent bowl: 10 bar (150 psig)
bowl: 17 bar (250 psig)
Metal bowl: 17 bar (250 psig)
Operating temperature*:
Operating temperature*:
Transparent bowl: –20° ... +50°C (0° ... +125°F) Metal
Technical features
Transparent bowl: –20° ... +50°C (0° ... +125°F)
bowl: –20° ... +65°C (0° ... +150°F)
Metal bowl: –20° ... +65°C (0° ... +150°F)
Fluid: Compressed air
* Air supply must be dry enough to avoid ice formation
* Air supply must be dry enough to avoid ice
Maximum pressure:
at temperatures below +2°C (+35°F). Particle remov-
formation at temperatures below +2°C (+35°F).
Guarded transparent bowl: 10 bar (150 psig)
al: Down to 0,01 µm
Particle removal: Down to 0,01 µm
Metal bowl: 17 bar (250 psig)
Air quality: Within ISO 8573-1, Class 1.7.2 Maximum
Air quality: Within ISO 8573-1, Class 1.7.2
Operating temperature*:
remaining oil content in outlet air: 0,01 mg/m3 at
Maximum remaining oil content in outlet air:
Transparent bowl: –20° ... +50°C (0° ... +125°F)
+21°C (+70°F)
0,01 mg/m at +21°C (+70°F)
3
Metal bowl: –20° ... +65°C (0° ... +150°F)
with an inlet concentration of 17 ppm Maximum flow
with an inlet concentration of 17 ppm
* Air supply must be dry enough to avoid ice
at 6,3 bar (90 psig) inlet pressure**: 16 dm3/s (34
Maximum flow at 6,3 bar (90 psig) inlet
formation at temperatures below +2°C (+35°F).
scfm) F64C, 28 dm3/s (60 scfm) F64H
pressure**: 16 dm /s (34 scfm) F64C, 28 dm
3
Particle removal: Down to 0,01 µm
** to maintain stated oil removal performance. Auto-
(60 scfm) F64H
Air quality: Within ISO 8573-1, Class 1.7.2
matic drain connection: 1/8"
** to maintain stated oil removal performance.
Maximum remaining oil content in outlet air:
Automatic drain operating conditions: Minimum
Automatic drain connection: 1/8"
0,01 mg/m at +21°C (+70°F)
3
pressure: 0,7 bar (10 psig). Drain openswhen bowl
Automatic drain operating conditions:
with an inlet concentration of 17 ppm
pressure drops below 0,2 bar (3 psig)
Minimum pressure: 0,7 bar (10 psig). Drain
Maximum flow at 6,3 bar (90 psig) inlet
Minimum air flow:
openswhen bowl pressure drops below 0,2 bar
pressure**: 16 dm /s (34 scfm) F64C, 28 dm
3
1 dm3/s (2 scfm) required to close drain Nominal bowl
(3 psig)
(60 scfm) F64H
size: 0,2 litre (7 fluid oz) Materials:
Minimum air flow:
** to maintain stated oil removal performance.
Body: Zinc
1 dm /s (2 scfm) required to close drain
3
Automatic drain connection: 1/8"
Bowl:
Nominal bowl size: 0,2 litre (7 fluid oz)
Automatic drain operating conditions:
Metal: Aluminium
Materials:
Minimum pressure: 0,7 bar (10 psig). Drain
Transparent, optional: Polycarbonate
Body: Zinc
openswhen bowl pressure drops below 0,2 bar
Metal bowl liquid level indicator lens, standard:
Bowl:
(3 psig)
Grilamid
Metal: Aluminium
Minimum air flow:
Metal bowl sight glass, optional: Pyrex Element:
Transparent, optional: Polycarbonate
1 dm /s (2 scfm) required to close drain
3
Composite materials
Metal bowl liquid level indicator lens, standard:
Nominal bowl size: 0,2 litre (7 fluid oz)
Elastomers: Synthetic rubber
Grilamid
Materials:
Mechanical service indicator materials:
Metal bowl sight glass, optional: Pyrex
Body: Zinc
Body: Transparent Nylon
Element: Composite materials
Bowl:
Internal parts: Acetal
Elastomers: Synthetic rubber
Metal: Aluminium
Spring: Stainless steel
Mechanical service indicator materials:
Transparent, optional: Polycarbonate
Elastomers: NBR
Body: Transparent Nylon
Metal bowl liquid level indicator lens, standard:
REPLACEMENT ITEMS Internal parts: Acetal
Grilamid
Service kit Spring: Stainless steel
Metal bowl sight glass, optional: Pyrex
contains required items circled: Elastomers: NBR
Element: Composite materials
Prismatic sight glass Replacement Items
Elastomers: Synthetic rubber
Pyrex sight glass
Service kit,
Mechanical service indicator materials:
contains required items circled: 4380-200
Body: Transparent Nylon
Pyrex sight glass
Prismatic sight glass
Internal parts: Acetal
Filter element:
Pyrex sight glass 4380-041
Spring: Stainless steel
F64C
Filter element:
Elastomers: NBR
F64C 4344-01
F64H
Replacement Items
F64H 4344-02
Service kit,
Manual drain
Manual drain 684-84
contains required items circled: 4380-200
Automatic drain
Automatic drain 3000-97
Prismatic sight glass
Mechanical service Indicator Mechanical service Indicator (1) 5797-50
Pyrex sight glass 4380-041
Installation
Filter element:
1.Install unit vertically in air line -
F64C 4344-01
• vertically (bowl down),
F64H 4344-02
• with air flow in direction of arrow on body,
Manual drain 684-84
• upstream of regulators, lubricators, and
Automatic drain 3000-97
cyclingvalves,
Mechanical service Indicator (1) 5797-50
Installation
1.Install unit vertically in air line -
• vertically (bowl down),
F64˙ – ˙˙˙ – ˙˙˙
Servive life indicator
D Mechanical service indicator
Servive life indicator
N Without indicator
D Mechanical service life
Thread
indicator
A PTF (1/8 PTF gauge ports)
N Without indicator
B ISO Rc taper (1/8 ISO Rc gauge ports)
G ISO G parallel (1/8 ISO Rc gauge ports)
N No thread (basic unit)
Servive life indicator
D Mechanical service indicator
N Without indicator
Thread
A PTF (1/8 PTF gauge ports)
INSTALLATION
• as close as possible to the air supply when
B ISO Rc taper (1/8 ISO Rc gauge ports)
1. Install unit vertically in air line -
used asa main line filter,
G ISO G parallel (1/8 ISO Rc gauge ports)
• vertically (bowl down),
N No thread (basic unit)
• as close as possible to the device being
• with air flow in direction of arrow on body,
serviced when used as a final filter.
• upstream of regulators, lubricators, and cycling-
2. Before assembling the basic unit into the yoke
valves,
the port seal o-rings should be lightly smeared
• as close as possible to the air supply when used asa
with o-ring grease.
• as close as possible to the air supply when
main line filter,
3. Locate clamp ring under lugs on top of yoke,
used asa main line filter,
• as close as possible to the device being serviced
offerbasic unit into yoke with directional
• as close as possible to the device being
when used as a final filter.
arrows correctly aligned (an interference fit
serviced when used as a final filter.
2. Before assembling the basic unit into the yoke the
prevents assembly if misaligned) before
2. Before assembling the basic unit into the yoke
port seal o-rings should be lightly smeared with
engaging and fullytightening the clamp ring.
the port seal o-rings should be lightly smeared
o-ring grease.
4. Turn bowl or bowl guard fully clockwise into
with o-ring grease.
3. Locate clamp ring under lugs on top of yoke, offer-
body before pressurizing. Lock symbols on
3. Locate clamp ring under lugs on top of yoke,
basic unit into yoke with directional arrows correct-
body andbowl guards must align.
offerbasic unit into yoke with directional
ly aligned (an interference fit prevents assembly if
/s 5. Auto-drain units may be fitted with a short
3
arrows correctly aligned (an interference fit
misaligned) before engaging and fullytightening
drain pipe and connector, minimum 5 mm
prevents assembly if misaligned) before
the clamp ring.
bore, to theG1⁄8 bottom outlet.
engaging and fullytightening the clamp ring.
4. Turn bowl or bowl guard fully clockwise into body
6. Push bowl, or bowl with guard, into body and
4. Turn bowl or bowl guard fully clockwise into
before pressurizing. Lock symbols on body andbowl
turnfully clockwise before pressurizing.
body before pressurizing. Lock symbols on
guards must align.
7. Install a Norgren general purpose filter with a
body andbowl guards must align.
5. Auto-drain units may be fitted with a short drain
5 µm element upstream of the oil removal filter
/s 5. Auto-drain units may be fitted with a short
3
pipe and connector, minimum 5 mm bore, to
to obtainmaximum element service life.
drain pipe and connector, minimum 5 mm
theG1⁄8 bottom outlet.
8. Turn bowl into body until arrowhead on bowl
bore, to theG1⁄8 bottom outlet.
6. Push bowl, or bowl with guard, into body and turn-
is aligned with or to the right of the arrowhead
6. Push bowl, or bowl with guard, into body and
fully clockwise before pressurizing.
on the body.
turnfully clockwise before pressurizing.
7. Install a Norgren general purpose filter with a 5
7. Install a Norgren general purpose filter with a
μm element upstream of the oil removal filter to
5 µm element upstream of the oil removal filter
obtainmaximum element service life.
to obtainmaximum element service life.
8. Turn bowl into body until arrowhead on bowl is
8. Turn bowl into body until arrowhead on bowl
aligned with or to the right of the arrowhead on
is aligned with or to the right of the arrowhead
the body.
on the body.
Servicing
1. Open manual drain to expel accumulated
liquids.Keep liquids below element (58, 60).
2. To operate automatic drain manually, lift
operatingpin in bottom outlet with a blunt rod.
3. Replace filter element when pressure drop
4380-200 acrosselement exceeds 0,7 bar (10 psig). The
Servicing
4380-040 mechanicalservice indicator shows
1. Open manual drain to expel accumulated
SERVICING
4380-040
approximately full red.
liquids.Keep liquids below element (58, 60).
1.Open manual drain to expel accumulated liquids.
Diassembly
2. To operate automatic drain manually, lift
4380-041
Keep liquids below element (58, 60).
4380-040 1. Shut off inlet pressure. Reduce pressure in
operatingpin in bottom outlet with a blunt rod.
2. To operate automatic drain manually, lift operating-
inletand outlet lines to zero.
3. Replace filter element when pressure drop
pin in bottom outlet with a blunt rod.
4344-01
2. For ease of maintenance the unit can be
acrosselement exceeds 0,7 bar (10 psig). The
3. Replace filter element when pressure drop acrosse-
removedfrom the yoke by unscrewing the
4344-02
mechanicalservice indicator shows
lement exceeds 0,7 bar (10 psig). The mechanical-
clamp ring, whichwill jack the unit out down
approximately full red.
684-84
service indicator shows approximately full red.
wards.
Diassembly
3000-97
3. Lift and turn the filter bowl counterclockwise
4380-040 1. Shut off inlet pressure. Reduce pressure in
(1) 5797-50 and remove with bowl o-ring.
inletand outlet lines to zero.
4. Disassemble in general accordance with the
2. For ease of maintenance the unit can be
item numbers on exploded view. Do not
removedfrom the yoke by unscrewing the
remove thedrains or the service indicator
clamp ring, whichwill jack the unit out down
unless replacementis necessary. Remove and
wards.
replace only if theymalfunction.
3. Lift and turn the filter bowl counterclockwise
and remove with bowl o-ring.
Our policy is one of continued research and development. We therefore reserve the right to amend,
4. Disassemble in general accordance with the
without notice, the specifications given in this document. (1999 - I&M8089d) © 2020 IMI International s.r.o.
item numbers on exploded view. Do not
Our policy is one of continued research and development. We therefore reserve the right to amend,
remove thedrains or the service indicator
without notice, the specifications given in this document. (1999 - I&M8075e) © 2015 IMI International s.r.o.
Installation & Maintenance Instructions
F64˙ – ˙˙˙ – ˙˙˙
Installation & Maintenance Instructions
Drain
A Automatic
F64˙ – ˙˙˙ – ˙˙˙ M Manual
Drain
Q Manual, 1/4 turn
A Automatic
M Manual
Q Manual 1/4 turn
Drain
A Automatic
M Manual
Q Manual 1/4 turn
A B
C
A B
C
F64C, F64H Filter
F64C, F64H Filter
Installation & Maintenance Instructions
F64C, F64H Filter
Element
0
Bowl
D Metal
Bowl
P Transparent with guard
D Metal
R Metal with Pyrex sight glass
P Transparent with guard
R Metal with Pyrex sight glass
Element
0
Bowl
D Metal
P Transparent with guard
R Metal with Pyrex sight glass
6
6
16
7
16
59
61
7
60 58
59
61
60 58
18
26
19
22
25
28
18
26
24
21
19 22
27
20
23
25
32
28
40
33 36
21 24
39
27
20
23
42
32
40
35 38
33 36
41
34
37
39
42
35 38
41
34
37
Element
0 Coalescing
Coalescing
Coalescing
8 1
2
4
3
8
1
5
2
4
3
5
31
30
29
31
30
29
47
48
46
45
44
43
47
48
46
45
44
43
01/22
IM/en 8.240.105 01
01/16
IM/en 8.240.10501