Advertisement
Quick Links
Advertisement
Related Manuals for FONROCHE LEKLA
Summary of Contents for FONROCHE LEKLA
- Page 1 INSTALLATION MANUAL TWIN LED SOLAR STREET LIGHT...
-
Page 2: How Does It Work
How does it work ? The battery gets loaded during daytime with the electricity produced by the solar panel (PV). Nighttime is detected by measuring the voltage of the solar panel : - daytime PV voltage > 30V - nighttime ... - Page 3 Maintenance - swap problem is found, claim damage to FONROCHE Lighting. The client is responsible for returning any defective part to FONROCHE Installation must comply with the installation manual ; Lighting for expertise. After receipt of the defective parts, FONROCHE Lighting all items provided must be installed otherwise the will determine the guarantee validity.
-
Page 4: Part List
Thread Tightening N° screw type torque (Nm) Part list > 10 > 24 3, 8, > 47,7 setscrews N° Reference Designation Quantity 1100001 Universal tool disconnect MC4 1108025 Washer M08 Inox A2-70-M 1108044 Screw TBHC M10x70 Inox A2 - 70 1108046 Washer M10 - M - Inox A2 - 70 1108047... - Page 5 Use an electrician needle (fish-tape) to draw the For all the assembly, every screw/nut system must be connector cables of the 2 lanterns through the bracket to tightened to the torque recommended by FONROCHE the top. Lighting* Page 5 of 16...
- Page 6 Make sure to put the nuts on the top of the lantern Insert the tube into the bracket Assemble the bracket on the pole and adjust it *See table on page 4 Insert the cable into the tube. Orient the lanterns, fasten slightly each pressure screw, and then tighten them all.
- Page 7 Assemble the base of the mounting kit Set to ° tilt (unless otherwise stated). Page 7 of 16...
- Page 8 Assemble the support for PV module Be careful to fit the screws n°8 in the same way as shown on the schematic to avoid any problem when installing the battery. Page 8 of 16...
- Page 9 Install the first PV mounting, Erect the streetlight on the ground Install only one PV mounting angle n°19 before erecting the pole. 4 & 5 Once the streetlight erected, go to step 9. Page 9 of 16...
- Page 10 Install the second PV mounting, Assemble the PV the battery and connect the lantern Same pieces as step 7 Pass the cable under the battery. Do not leave the cables hanging under the support. Page 10 of 16...
- Page 11 Orient the PV towards the equator Orient the PV towards the equator, Tighten the 8 pressure screws, Position the lanterns straight in order to optimize the lighting Page 11 of 16...
- Page 12 Initialize the battery Connect the PV to the battery Please wait 30 seconds after plugging for system activation Page 12 of 16...
- Page 13 Validate your installation Disconnect only one connector of the PV with the “Universal tool disconnect” n°1. Page 13 of 16...
- Page 14 Wait 1 min max, light must switch ON Then you can reconnect the PV Wait another min max, light must switch OFF Light If light switches OFF, installation is OK. You can then bind all the cables with cable ties. Page 14 of 16...
-
Page 15: Troubleshooting
Last step of installation – Check-list Installer check Check points (write OK or Are lanterns straight positioned to optimize the lighting ? Are the 16 pressure screws installed and correctly tightened ? Is the PV oriented towards the equator ? If several solar street lights are installed, are the PVs oriented towards the same direction ? Is the PV set to 20°... - Page 16 Batteries are discharged Check tilt angle and orientation of the solar module. several days Wait some days if it is winter, if not call FONROCHE Lighting for further actions. For any other problem, please contact FONROCHE Lighting Page 16 of 16...
Need help?
Do you have a question about the LEKLA and is the answer not in the manual?
Questions and answers