Advertisement
Quick Links
Advertisement
Related Manuals for FONROCHE LEKLA
Summary of Contents for FONROCHE LEKLA
- Page 1 INSTALLATION MANUAL SIMPLE BRACKET SOLAR STREET LIGHT...
-
Page 2: How Does It Work
How does it work ? The battery gets loaded during daytime with the electricity produced by the solar panel (PV). Nighttime is detected by measuring the voltage of the solar panel : Avoid any shadow on the solar panel (trees, houses, traffic signs…). Shadows will considerably impact electricity production of the panel and hence reduce recharging of the battery. - Page 3 Maintenance - swap Likewise, control the right fit bracket/pole, if any operating The client is responsible for returning any defective part to FONROCHE problem is found, claim damage to FONROCHE Lighting. Lighting for expertise. After receipt of the defective parts, FONROCHE Lighting will determine the guarantee validity.
- Page 4 Part list 1100001 Universal tool disconnect MC4 1108025 Washer M08 Inox A2-70-M 1108044 Screw TBHC M10 x 70 Inox A2-70 1108046 Washer M10 - M - Inox A2-70 1108047 Grower Washer M10 - Inox A2 - 70 1108048 Nut M10 Inox A2 - 70 1108058 Grower Washer M08 - Inox A2-70 1108063...
- Page 5 Set the luminary Assemble the luminary on the bracket Use a draw wire (fish-tape) to draw the connector cable of the lantern through the bracket to the top. Be careful setting the nuts on the top side of the luminary Page of...
- Page 6 Insert the tube into the bracket Assemble the bracket on the pole and orientation Insert the cable into the tube. Orient the luminary, fasten slightly each setscrew, and then tighten them all. Page of...
- Page 7 Assemble the base support Se t to ° (unless otherwise stated). Page of...
- Page 8 Assemble the support for PV modules Be careful to set the screws n°8 in the same way as illustrated in the scheme to avoid any problem when installing the battery. Page of...
- Page 9 Install the first PV binding, on Erect the street light the ground Install only one PV binding n°15 before erecting the pole 4 & 5 Once the street light erected, go to step 9. Page of...
- Page 10 Install the second binding, the Assemble the PV battery and connect the luminary Box Energy Labels up Same steps as step 7. Pass the cable under the battery. Energy Box label should be positioned always to upside (direction to PV). Do not leave the cable hanging under the support.
- Page 11 Orient the PV to the south Orient the PV towards the equator, Tighten the 8 setscrews, Position the luminaries straight in order to optimize the lighting. Page...
-
Page 12: Please Wait
Initialize the battery Connect the PV to the battery Please wait 30 seconds Page... - Page 13 Validate your installation Detach one connector of each PV with the « Universal tool disconnect » n°1. Page...
- Page 14 Light ON If light switches OFF, installation is OK. You can bind all the cables with cable ties. Page...
- Page 15 Last step of installation – Check-list Installer check Check points (write OK or no) Are lanterns straight positioned to optimize the lighting ? Are the 16 pressure screws installed and correctly tightened ? Is the PV oriented to the south ? If several solar street lights are installed, are the PVs oriented towards the same direction ? Is the PV set to 20°...
-
Page 16: Troubleshooting
Check the connections of the solar module. Check that there is no shadow on the solar module. Batteries are discharged Check tilt angle and orientation of the solar module. Wait some days if it is winter, if not call FONROCHE Lighting for further actions. Page...
Need help?
Do you have a question about the LEKLA and is the answer not in the manual?
Questions and answers