Advertisement
Quick Links
Advertisement
Related Manuals for Dantherm CC3000
Summary of Contents for Dantherm CC3000
- Page 1 Upgrade kit CC3000 controller Part no. 094838 28.02.2017...
-
Page 2: Table Of Contents
Make sure that the power to the unit is disconnected before you start the installation. Table of Contents This service manual covers the following topics: Topic See page General information Included in the kit Installation procedure Installing the CC3000 with Flexibox 450 and DFC 350/450 System setup Default cooling strategy. Declaration of conformity... -
Page 3: Introduction
General information Introduction The CC3000 is an advanced controller that can control two Free cooling units and two A/C. This kit is for replacement of TKS3000 and ACUE Controllers installed at free cooling units. Manual, part no. Part number of this service manual is 094927. -
Page 4: Installation Procedure
Installation Schematic installation Installation procedure Follow these steps to install the CC3000 upgrade Kit for Free Cooling Units. Step Action Make sure that the power to the Free Cooling Units is disconnected. Find a location for satellite box and the CC 3000. -
Page 5: Installing The Cc3000 With Flexibox 450 And Dfc 350/450
Installing the CC3000 with Flexibox 450 and DFC 350/450 Step 4 48V DC FB 450 DC DC Satellite Box Flexibox Cable Black 1 Black 3 48V DC Black 4 Black 2 Black 5 Black 6 Outdoor Sensor Outdoor Sensor Cable 8 wire... - Page 6 Installing the CC3000 with Flexibox 450 and DFC 350/450, continued Step 4 230V AC FB 450 AC AC Satellite Box Flexibox Cable 1 Brown Blue Green/yellow 230V AC Flexibox Cable 2 Black 1 Black 2 Black 3 Black 6 Black 5...
- Page 7 Installing the CC3000 with Flexibox 450 and DFC 350/450, continued Step 4 DFC 48V 350/450 DC DC Satellite Box Flexibox Cable Black 1 Black 3 48V DC Black 4 Black 2 Black 5 Black 6 Outdoor Sensor Outdoor Sensor Cable 8 wire...
- Page 8 Installing the CC3000 with Flexibox 450 and DFC 350/450, continued Step 4 230V AC 350/450 AC AC Satellite Box Flexibox Cable 1 Brown Blue Green/yellow 230V AC Flexibox Cable 2 Black 1 Black 2 Black 3 Black 6 Black 5...
- Page 9 Step 5 4 x Ø3mm CC3000 350/450 DC Break away to integrate cable trays Fasten main part to the wall mount Access connectors Remove front cover to access connectors Use two screws in the stand-offs to secure Press to release...
-
Page 10: System Setup
4 3 2 1 System setup At startup insert SD card in the slot located on the side of the CC3000 controller. This will allow you to select the config file for your free cooling system.. Note: until the SD card is inserted the controller will remain inactive and the buttons will not function. -
Page 12: Default Cooling Strategy
Default Cooling strategies (can be changed using the CC3000 controller. ) TTL link The TTL link interface is used for service / test purposes. System status information can be read out. Configuration and settings can be changed. Override function to verify correct connection of system components like Free cooling unit , dampers, sensors, etc. - Page 13 Default Cooling strategies, continued Description Value Free Cooling Mode Temperature when fan stops Temperature when Fan starts Min °C Temperature at bottom of P-band Max °C Temperature at top of P-band The wanted indoor temperature; fan speed will be adjusted between Set Point Min°C and Max °C Emergency on...
- Page 14 Default Cooling strategies, continued Standard Mode Description Value (Freecooling <> A/C) Temperature when fan stops Temperature when Fan starts Min °C Temperature at bottom of P-band Max °C Temperature at top of P-band The wanted indoor temperature; fan speed will be adjusted between Set Point Min°C and Max °C A/C 1 on...
- Page 15 Default Cooling strategies, continued Description Value Energy save Mode temperature when fan stops (Freecooling > A/C) Temperature when Fan starts Min °C temperature at bottom of P-band Max °C Temperature at top of P-band The wanted indoor temperature; fan speed will be adjusted Set Point between Min°C and Max °C A/C 1 on...
- Page 16 Default Cooling strategies, continued Description Value Air Conditioner Mode Set Point External Air Con unit 1 start if connected A/C 1 off External Air Con unit 1 stops if connected A/C 2 on External Air Con unit 2 start if connected A/C 2 off External Air Con unit 2 stops if connected Emergency on...
-
Page 19: Declaration Of Conformity
Declatation of conformity Dantherm Air Handling A/S Marienlystvej 65 DK - 7800 Skive Tel.: +45 96 14 37 00 Fax: +45 96 14 38 00 Declaration of following product: CC3000 Ugrade kit Product name: Product No: 094838 • 2006/42/EC Directive on the safety of machines •... - Page 20 Dantherm n’assume aucune responsabilité pour erreurs et modifications éventuelles. Dantherm se exime de cualquier responsabilidad por errores y cambios realizados. A Dantherm recusa qualquer responsabilidade relacionada com eventuais erros e alterações. Компания Dantherm не принимает на себя ответственность за возможные ошибки и изменения в настоящем документе.