V-Drums TD-02K Setup Manual

Setup Guide
TD-02K
Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
1
Drum stand
7
1 2 3 4 5 6
Assemble the drum stand
2
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland
to prevent the rubber feet from soiling the surface on which they are placed.
* The drum stand assembly procedure is for right-handed players. If you want to set up the stand for left-handed players, refer to "Assembly for left-handed
players" in the lower right.
1. Assembling the left and right arm sections
Left arm Left arm Right arm Right arm
* Lay the left and right arm sections on the floor while assembling them.
Left arm section
1–1.
Use the drum key to loosen the bolt of the left leg
1
holder, and insert the left arm .
2
Drum
key
Left arm
2
Left
1
leg
1–2.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
* Adjust the hi-hat rod holder of the left arm and the L-shaped
2
pipe holder so that they are facing the same way, as shown in the
illustration.
Hi-hat rod holder
Left arm 2
L-shaped pipe holder
Right arm section
1–3.
Use the drum key to loosen the bolt of the right leg ,
6
and insert the right arm .
5
1–4.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
Bolt
Right arm 5
Holder
Right
6
leg
Attach the parts
3
NOTE
Be careful not to get your fingers pinched by the movable parts when you operate the drum
* Adjust the position and height of the pads and
sound module holder, the hi-hat control pedal, the kick pedal or the cymbals. If using this in
pedals according to your build and preferences,
a location where children are present, be sure to provide adult supervision or guidance.
so that they are easy to play.
Attaching the crash cymbal/ride cymbal (CY-5)
Insert the cymbal onto the top of the cymbal
rod.
Attaching the hi-hat (CY-5)
* Use the cymbal nut included with the drum stand to attach the hi-hat.
1.
Cymbal nut
Insert the cymbal so that the
stopper (convex portion) on the
hi-hat rod fits into the concave part
on the bottom of the cymbal.
2.
Tighten the cymbal nut enough
"Roland" logo on the
to prevent the pad from wobbling
farther side
Rotation
when you strike it.
stopper
(convex
portion)
Adjusting the position of the cymbal
Not
Adjust the height of
OK
the cymbal rod so that
OK
the highest point of the
cymbal is 115 cm or less.
115 cm
8
No. Name Quantity
Left leg 1
1
Left arm 1
2
Hi-hat rod 1
3
Center pipe 1
4
9
Right arm 1
5
Right leg 1
6
10
Cymbal rod 2
7
Cymbal rod holder 2
8
Top pipe 1
9
L-shaped pipe
2
10
11
Cable clip 4
11
2. Attaching the left/right arm sections onto the center pipe
Center pipe Center pipe
Right arm Right arm
Left arm Left arm
2–1.
Use the drum key to loosen the bolt of holder A, which
is attached to the center pipe , and push it down to
4
the left. Insert the left arm you assembled in step 1 into
holder A.
Center pipe 4
Holder A
bolt
2–2.
Once the pipe is fully inserted, firmly tighten the bolts (2)
of holder A with the drum key.
Holder A
Fully
Temporarily tighten
tighten
2–3.
Use the drum key to loosen the bolt of holder B, and
insert the right arm you assembled in step 1 into holder
B of the center pipe .
4
Holder B
Bolt
Right arm
Center pipe 4
2–4.
Once the pipe is fully inserted, tighten the bolts (2) of
holder B with the drum key.
Fully tighten
Temporarily
tighten
Attaching the drum sound module (TD-02)
1. 2.
Use the bolt for the drum sound module Loosen the bolt of the drum sound module
holder to attach the drum sound module holder, attach the holder onto the top of
to the holder. the center pipe and tighten the bolt.
Drum sound module holder
Bolt
TD-02 TD-02
CY-5 CY-5 CY-5 CY-5
PD-4 PD-4 PD-4 PD-4
CY-5 CY-5
PD-4 PD-4
Hi-hat control pedal Hi-hat control pedal
Kick pedal Kick pedal
* To prevent the drum stand from tipping over,
do not position the stand leg pipes at either
end more than 1 meter apart.
1 m
Attaching the snare and
toms (PD-4)
Attach the cymbal OK Not
OK
rods so that they
face straight up, to
prevent the drum
stand from falling L-shaped L-shaped
pipe pipe
over.
Before using this unit, carefully read "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (in the leaflet "USING THE UNIT SAFELY" and in the TD-02K Setup Guide). After reading, keep the document(s) where
it will be available for immediate reference.
Drum sound module, pads, other items
* See "Hi-hat control pedal, kick pedal" on the back
side for how to distinguish between the pedals.
 Kick pedal (KT-1)
 Hi-hat control pedal (FD-1)
 Cymbal pad for Hi-hat/ride/
crash (CY-5 x 3)
 Drum sound  Drum sound module  Dedicated
module holder (TD-02) connection cable
NOTE
• Be careful not to get your fingers pinched by the movable parts when you set up or adjust the drum stand. If using this in a location where
children are present, be sure to provide adult supervision or guidance.
• Be sure that there is plenty of space to safely assemble this instrument.
• Do not use a power tool (e.g., an electric screwdriver) to assemble this instrument. Doing so may damage the screws.
• Do not overtighten the bolts.
• Be careful not to get grease from the bolts on your hands or other items.
3. Adjusting the vertical pipes
3–1.
Place the center pipe upright, and adjust the angle so
4
that the drum stand can stand up by itself.
3–2.
Firmly tighten the bolts (2) of holders A and B that you
temporarily tightened in step 2.
Holder A and B bolts that were
temporarily tightened in step 2
3–3.
Make sure that the three vertical pipes remain fully
upright, and that the left/right arms are fully horizontal.
Attaching the L-shaped pipe
4.
L-shaped L-shaped
L-shaped L-shaped pipe pipe
pipe pipe
4–1.
Use the drum key to loosen the bolt of the L-shaped
pipe holder for the left arm , and insert the
2
L-shaped pipe .
10
4–2.
Use the drum key to firmly tighten the bolt.
L-shaped pipe 10
L-shaped pipe holder
Left arm 2
Bolt
4–3.
Use the drum key to loosen the bolt of the L-shaped
pipe holder for the right arm , and insert the
5
L-shaped pipe .
10
4–4.
Use the drum key to firmly tighten the bolt of the
L-shaped pipe holder.
L-shaped pipe 10
L-shaped pipe holder
5
Right arm
Bolt
4 Connect the pads to the drum sound module (TD-02)
Connection procedure
1.
Connect the dedicated
connection cable to the drum
sound module as shown in the
illustration below.
Insert the connector all the
way, then turn the knobs to
lock it in place.
Knob
For a left-handed setup
PD-4 PD-4
Assemble the drum stand as described in
"Assembly for left-handed players" in the "
Assemble the drum stand" section, and then
attach the parts and connect the cables as
shown in the illustration at right.
Drum
key This completes assembly and connections.
 Pad for Snare/tom (PD-4 x 4)
 AC adaptor  Drum key
5. Attaching the top pipe
5–1.
Loosen the hand knob on the top of the center pipe .
4
5–2.
Rotate the holder so that the bolt faces forward, and
firmly tighten the hand knob.
Hand knob
Bolt
Holder
Center pipe Center pipe 4
5–3.
Insert the top pipe into the holder, and use the drum key
to firmly tighten the bolt.
Top pipe
9
Bolt
Holder
Attaching the tom pads (T1, T2) and cymbal rod holder
6.
6–1.
Insert the toms through the top pipe , and use the
9
drum key to firmly tighten the bolts (2).
T1 T1 T2 T2
Top pipe Top pipe
9
Drum
key
6–2.
Attach the cymbal rod holder onto the end of the top
8
pipe , and firmly tighten the bolts (2) with the drum
9
key.
* Attach the cymbal rod holder so that its vertical bolt is on the back side
of the stand and the heads of its horizontal bolts are on the outside of
the stand, as shown in the illustration.
Drum
key
Bolt head
Bolt head
Drum
key
Cabling diagram for the dedicated connection cable
(as seen from the back)
2.
Labels indicating the pad to
be connected are attached
RD
to the dedicated connection TD-02
cable. Connect the cables by
referring to the illustration
T2
at right.
T3
* Insert the plug firmly,
making sure it's all the CR2
way in.
Label KIK
( ( CR1 CR1) )
( ( RD RD) )
CY-5 CY-5
CY-5 CY-5 TD-02 TD-02
2
( ( T1 T1) )
( ( T2 T2) )
PD-4 PD-4 PD-4 PD-4 ( ( HH HH) )
CY-5 CY-5
( ( T3 T3) )
( ( SNR SNR) )
PD-4 PD-4
PD-4 PD-4
Kick pedal Kick pedal Hi-hat control Hi-hat control
pedal pedal
à When you've finished making connections, turn on the power as described on the
back side of the "Quick Start" document, and verify that you can hear the sound.
© 2022 Roland Corporation
Accessing the TD-02 Accessing the TD-02 Accessing the Accessing the
Owner's Manual Owner's Manual video manual video manual
You can scan the
Refer to the "Owner's
following 2D code to see
Manual" (Roland website)
a quick start video. This
for details on how to use
video explains the steps
TD-02.
for assembly.
Use this 2D code to
access the website.
7. Attaching the cymbal rod and hi-hat rod
7–1.
Lock the hi-hat rod holder in place so that its insertion
hole is facing to the back of the stand.
7–2.
Insert the hi-hat rod , the ride cymbal rod and the
3 7
crash cymbal rod into the holders, and adjust the
7
position and direction of all holders as shown in the
illustration to complete the setup.
NOTE
The tip of the cymbal rod is sharp. Handle it with care.
Cymbal rod
7
Tilt towards the player
Face the slanted
side towards the
player
Hi-hat rod
3
Assembly for left-handed players
If you want to use a left-handed setup, assemble the stand as
follows.
• Attach the hi-hat rod holder of the left arm 2 onto the right side of
the right arm 5 .
• Attach the L-shaped pipe 10 onto the L-shaped pipe holder of the
right arm 5 (insert the long pipe), and attach the hi-hat rod 3
onto the hi-hat rod holder.
• Attach the L-shaped pipe (insert the short pipe) onto the
10
L-shaped pipe holder of the left arm 2 .
Cymbal rod
7
Hi-hat rod
3
L-shaped pipe L-shaped pipe
10
Right leg Right leg
Left leg Left leg
1 6
* Use cable clips to fasten the
11
cables so that they don't obstruct
your playing.
CR1
We recommend attaching the
clips in the locations shown with
T1
HH
a .
SNR
"CR2" is not used. You can use a
separately sold cymbal set (OP-
TD1C) to add more cymbals. If
you are not adding this, leave
the cap attached. Fasten it so
that it does not obstruct your
HHC performance.
Cabling diagram for the dedicated
connection cable
(As seen from the back)
CR1 RD
TD-02
T1 T2
HH
T3
SNR
CR2
HHC KIK
"CR2" is not used. You can use a separately sold cymbal set
(OP-TD1C) to add more cymbals. If you are not adding this,
leave the cap attached. Fasten it so that it does not obstruct
your performance.