V-Drums TD-17KVX Setup Manual

TD-17KVX
Check the included items
01
MDS-4KVX
* When checking the items
included with the MDS-
4KVX refer to "MDS-4KVX
Owner's Manual. "
8 Kick pad (KD-10)
Assemble the stand
02
* The tip of the mount is sharp. Handle it with care.
* When setting up or storing the stand, be careful not to pinch the fingers you use to
handle the stand.
Assembly procedure
Assemble the stand using the procedure described in "MDS-4KVX Owner's Manual. "
Loosen this hand knob, and rotate the
mount holder (L) 90 degrees in the direction
of the arrow.
Cymbal mounts
Pad mounts
Pad mounts
If the stand wobbles, loosen
this hand knob and adjust
the height.
* For reasons of safety, do not spread the stand
wider than 1.2 meters (47 inches).
Connect the pads to TD
04
Connection procedure
1. 2.
Connect the cable to TD as Labels indicating the pad to
shown in the illustration. be connected are attached
to the cable. Connect the
Insert the connector all the
cable to the OUTPUT jack of
way, then turn the knobs to
each pad as shown in the
fasten it securely.
illustration.
* Insert the plug firmly,
making sure it's all the
way in.
Knob
Attaching the TD to a different location
You can change the location at which the TD is attached,
so that the hi-hat stand is on the outside as shown in the
illustration.
1.
Position the sound module mount as shown in the illustration below,
and attach it to the TD.
2.
Of the mount holders of curved pipe (L), insert the sound module
mount into the mount holder to which the cymbal mount is not
attached.
This completes assembly and connections.
Setup Guide
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
* This package does not include a kick pedal, and a hi-hat stand. Use with a commercially available kick pedal, hi-hat stand, and snare stand.
8 V-Cymbal for crash 8 V-Cymbal for ride
8 V-Hi-hat (VH-10)
(CY-12C x 2) (CY-13R)
Attach the parts
03
Attach the hi-hat (VH-10)
Motion Sensor Unit
CONTROL OUT jack on the
farther side
Insulating Plate
Sponge side up
Cymbal mount
Compatible hi-hat stand
Diameter: 6.0–7.0 mm
(0.236"–0.276")
Diameter: 11.7 mm (1/2")
Max.
Adjusting the position of the cymbal
Adjust the height of the rod so that the highest point of the cymbal is
1.2 m
less than 1.2 meters.
BOW/EDGE
RD plug
OUTPUT jack
3.
Using the included trigger cable,
BELL
RDB plug
connect crash cymbal 2 to the OUTPUT jack
TD's CRASH 2 jack.
* Fasten the cables so that they will
Symbal side not obstruct your playing; use cable
clips and cable ties.
Make sure to wrap the cable ties
around the pipes.
TD-17 side
For a left-handed setup
The setup described in this guide is for right-handed players. To set up for a left-handed player,
reattach the components as follows.
5 Exchange curved pipes (L) and (R), and straight pipes (L) and (R), left-for-right.
5 Attach holder (C) and the snare pipe to the right side.
5 Exchange the pads and cymbals with their attachment mounts left-for-right.
5 Exchange the TD with its sound module mount left-for-right.
Connect the cables as shown in the illustration.
As seen from the back
Using the included trigger cable, connect crash cymbal 2 to the TD's
CRASH 2 jack.
In order to use this device correctly, please carefully read "Using
the Unit Safely" and "Important Notes" (included in each owner's
manual) before use.
Parts of the TD-17KVX
8 V-Pad for snare (PDX-12) 8 V-Pad for tom
8 Drum sound module (TD)
(PDX-8 x 3)
(TD-17)
(Be sure to orient it correctly)
Attach the stopper so that
the bolt is on the right-hand
Clutch screw
side, from the performer's
perspective.
Hi-Hat
"Roland" logo on the
farther side
Attach the TD
1.
Align the protrusions of the
sound module mount with the
rails of the TD, and slide it in until
you hear it click.
2.
Loosen the hand knob of the
mount holder, and insert the
sound module mount.
3.
Adjust the angle of the TD, and
then tighten the hand knob.
Attach the kick pedal (KD-10)
1.2 m
As seen from the back
Connection cable
Trigger cable
HH plug
RD RDB
CR1
Crash
Cymbal 2 T2 T1
HHC plug
HH
HHC
T3 TD-17
SNR
KIK
RD RDB
CR1
HHC
HH
Crash
T1 T2
Cymbal 2
SNR
T3
TD-17
KIK
9
When you've finished making connections, turn on the power as described in the TD-17/17-L Owner's Manual, and
verify that you can hear sound.
8 Connection cable 8 Trigger cable 8 AC adaptor
(special for TD)
Attach the crash cymbal (CY-12C) and ride cymbal (CY-13R)
Tighten the bolt with a drum key.
Tighten the wing nut to
Stopper
obtain an appropriate
amount of sway.
CY-12C
PDX-8 PDX-8
VH-10
TD-17
PDX-12
KD-10
Attach the snare (PDX-12) and toms (PDX-8)
Tighten
Loosen
Install the kick pedal securely.
Rod
Attach the cymbal so that its center does not extend toward the back
beyond the pipes of the stand (the pipes at the back of the stand).
Connect the AC adaptor
05
and speakers
TRIGGER OUT
Jack
Connect the AC adaptor, speakers, or headphones as described in the
owner's manual of the TD.
CONTROL OUT
Jack
* To prevent malfunction and equipment failure, always turn down the volume, and turn
off all the units before making any connections.
(RD) (RDB)
CY-13R
CY-12C
(T3)
PDX-8
Connection cable
Curved pipe R
Trigger cable
(including the pad mount)
Straight pipe R
(short)
After exchanging the curved pipes, attach Mark
the holders so that the marks on the pipes
Remove the caps, remove holder (C) and the snare pipe,
are visible through the gaps of the holders.
and reattach them to the right side.
© 2018 Roland Corporation
8 Setup Guide (this document)
8 Owner's manual set
"Roland" logo on the farther side
Wing nut
Felt washer
CY-13R
CY-12C
PDX-8
Adjust the location at which
the KD-10 is installed so that
it's at a comfortable position
for playing.
Tighten
Loosen
Rod
OK Not OK
(CR1)
CY-12C
(T2) (T1)
PDX-8 PDX-8
(HH)
VH-10
TD-17
(SNR)
PDX-12
(KIK)
KD-10
Curved pipe L
Straight pipe L (long)