V-Drums TD-07DMK Setup Manual

* 5 1 0 0 0 7 6 4 3 8 -
TD-07DMK
Check the included items
1
2
1
3 4 5 6 7
Assemble the drum stand
2
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat
(TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.
* The drum stand assembly procedure is for right-handed players. If you want to set up the stand for left-handed players, refer to
"Assembly for left-handed players" in the lower right.
1. 2.
Attaching the parts for the kick Assembling the left and right arm sections
* Lay the left and right arm sections on the floor
1–1.
Remove the cap that is attached to the
1 while assembling them.
main unit's right pipe (with one holder).
Left arm section
1–2.
Insert the kick pad and mount holder (for the
2–1.
pedal plate), and provisionally fasten them in
Using a drum key, loosen the bolt on the
the orientation shown in the illustration.
holder of straight pipe "L" (long)
insert curved pipe
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
2–2.
After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
Kick pad
Wide Narrow
Mount holder
(for the pedal plate)
Cap
2–3.
Use the drum key to loosen the bolt of the
1–3.
Replace the cap.
drum sound module holder, then attach the
1–4. drum sound module holder to straight pipe
Attach the pedal plate to the mount holder.
"L" (long)
Drum sound module
Pedal plate Right arm section
2–4.
Using a drum key, loosen the bolt on the
holder of straight pipe "R" (short)
insert curved pipe
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
2–5.
After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
2–6.
Position straight pipe "R" (short)
tip protrudes by about 7 cm (3 inches), and
then tighten the holder.
Attach the parts
3
* Adjust the position and height of the pads and pedals according
to your height and tastes, so that they are easy to play.
Attach the hi-hat (CY-5), crash cymbal/ride cymbal (CY-8)
* Use the cymbal nut and felt washer that are included with the drum stand.
1.
Position the cymbal so that the stopper (convex
Cymbal nut
portion) of the cymbal mount is aligned with the
Felt washer
concave portion of the bottom of the cymbal.
"Roland" logo on the
farther side
* To prevent the drum stand from tipping over,
Stopper
do not position the stand leg pipes at the two
(convex
ends more than 1.2 meters (48 inches) apart.
portion)
Attach the drum sound module
1.2 m (48 inches)
(TD-07)
Use the bolt of the drum sound module
holder to attach it as shown in the
illustration.
* When attaching the PDX-8 (snare),
refer to "About the memory clamp"
on the other side.
Attach the kick pedal
1. 2.
Mount the kick pedal to the Adjust the position of
pedal plate. the kick pad and the kick
pedal so that the beater
strikes the center of the
Install the kick pedal
kick pad when you step
securely.
on the kick pedal.
Verify that the plate and pedal firmly
contact the floor without any gap
Adjusting the position of the cymbal
Use caution regarding the
following to prevent the drum
OK
stand from falling over.
5 Adjust the rod height so
1.2 m
that no part of any cymbal
(48 inches)
is higher than 1.2 meters (48
inches) above the floor.
0 1 *
Setup Guide
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
* This package does not include a kick pedal. Use with a commercially available kick pedal.
Drum stand
No. Name
1 Main unit
9
Curved pipe
2
Straight pipe L (Long)
3
Straight pipe R (Short)
4
Snare pipe
5
10
8 Cymbal mount (Short)
6
Cymbal mount (Long)
7
11
Mount holder
8
Pad mount
9
12
Pad mount (with the memory clamp)
10
Cable clip
11
Cable tie
12
3.
Attach the left/right arm sections to the main unit
3–1.
Use a drum key to loosen bolt of the holder
"A" attached to the left-side pipe (with two
holders) of the main unit
arm (of the assembly you created in step 1)
into holder "A" of the main unit.
, then
3
. Bolt
2 Left arm
Curved pipe 2
Holder A
Holder
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
Drum key
Curved pipe 2
Guide hole
Guide hole
Bolt
Straight pipe L (Long) 3
3–2.
After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
3–3.
Lower the holder "B" attached to the main
unit 's right pipe, moving it down to the
1
and tighten the bolt. position shown in the illustration.
3
Bolt
holder
Straight pipe L
3
(Long)
3–4.
Use the drum key to loosen bolt of the holder
"B," and insert right arm (of the assembly you
created in step 1) into holder "B" of the main
unit .
1
then
4
.
2
Holder B
* As a general rule, insert curved pipe until the guide hole on
the pipe can be seen through the gap in the holder.
Bolt
about 7 cm (3 inches)
Curved pipe 2
Holder
Guide hole
Straight pipe
3–5.
4 After firmly inserting it all the way, use the
R (Short)
drum key to firmly tighten bolt.
so that its
4
NOTE
When handling the hi-hat control pedal, kick pedal, or cymbal pads, take care not to
pinch your fingers between movable parts and the main unit. If using this in a location
where children are present, be sure to provide adult supervision or guidance.
2.
Hi-hat:
Tighten the cymbal nut enough to prevent the pad from
wobbling when you strike it.
Crash/Ride cymbal:
Tighten the cymbal nut enough to allow an appropriate
amount of sway.
CY-5
PDX-6A PDX-6A
CY-5
TD-07
PDX-8 PDX-6A
Hi-hat control
pedal
3.
Once the kick pad and kick
pedal are in the desired
playing position, tighten
Kick pad
Beater
the hand knobs.
Hand knob
Attach the snare (PDX-8)
and toms (PDX-6A)
OK Not OK
Tighten
5 Attach the cymbals in
Loosen
such a way that the
center of the cymbal
does not extend
beyond the rear pipes
of the stand.
Before using this unit, carefully read "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (the leaflet "USING THE UNIT SAFELY, " "TD-07 Owner's Manual, " and the Setup Guide).
After reading, keep the document(s) where it will be available for immediate reference.
Quantity
1
2
1
1
8 Kick pad 8 Mount holder
1
(for the pedal plate)
2
1
3
3
1
8 Cymbal pad for hi-hat/crash/ride
4
(CY-5 x 3)
2
NOTE
5 When setting-up or adjusting the drum stand, take care not to pinch your fingers between movable parts and the main unit. If using this in a location where children
are present, be sure to provide adult supervision or guidance.
5 Prepare an area in which you can perform the assembly safely.
5 Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
4.
Attaching the snare pipe
4–1.
Use the drum key to loosen bolt of the holder
"C," and insert the snare pipe
, and insert left
1 "C" of the main unit 1 .
4–2.
After firmly inserting it all the way, use the
drum key to firmly tighten bolt.
Main unit 1
* Insert the end of the snare pipe that doesn't have a cap on it
into holder "C. "
Bolt
Holder C
Cap
Bolt
Snare pipe
5
5.
Adjusting the vertical pipes
5–1.
Place the main unit upright, then loosen
1
the hand knobs of holders "A" and "B." Next,
spread open the pipes at left and right.
5–2.
Adjust to an angle at which the drum stand
can remain upright on its own, and then
tighten the hand knobs (two locations) that
you loosened.
about 7 cm (3 inches)
5–3.
Verify that the four vertical pipes are truly
Holder B
vertical.
If the stand wobbles, loosen the bolts on the
holders of straight pipes "L" (long)
(short) and adjust the height. After adjusting
4
the height, tighten the bolts on the holders.
Hand knobs of
holders A and B
Bolt
Right arm
Curved pipe 2
Bolt
Guide hole
Bolts on the holder
Connect the pads to the drum sound module (TD-07)
4
Connection procedure
1.
Connect the connection cable to the
drum sound module as shown in the
illustration below.
Insert the connector all the way, then
turn the knobs to fasten it securely.
Knob
CY-5
Connect the AC adaptor and headphones/speakers
5
Connect the AC adaptor, headphones, or speakers as
described in the "TD-07 Owner's Manual. "
* To prevent malfunction and equipment failure,
always turn down the volume, and turn off all the
units before making any connections.
For a left-handed setup
Assemble the drum stand as described in
"Assembly for a left-handed players" of section
" Assemble the drum stand"; then attach the
2
parts and connect the cables as shown in the
illustration at right.
Pad mount
This completes assembly and connections.
Drum sound module / Pads / Others
8 Pedal plate 8 Drum sound 8 Drum sound module 8 Connection cable
module holder (TD-07)
* PDX-6A does not support
the use of the rim-shot
technique.
8 Hi-hat control 8 V-Pad for snare 8 V-Pad for tom
pedal (PDX-8) (PDX-6A x 3)
6.
Attaching the pad mounts
NOTE
into holder
5
The tips of the mounts are sharp. Handle them with
care.
Main unit/snare pipe
6–1.
Attach mount holders to the top of the
8
main unit and tighten the respective hand
1
knobs.
Mount holders 8
Hand knobs
6–2.
Attach the pad mounts to mount holder
9
, and firmly tighten the respective hand
8
knobs.
Pad mounts 9
Hand knobs
6–3.
Attach mount holder to the snare pipe
8
and tighten the hand knob.
Hand knob
and "R"
3
8
Mount holder
6–4.
Attach pad mount (with memory clamp)
to the snare pipe , and tighten the hand
5
knob.
Pad mount
(with the memory clamp)
10
Hand knob
Right arm
6–5.
Attach pad mount to the mount holder
9
, and tighten the hand knob.
8
Pad mount 9 Mount holder 8
Hand knob
* Fasten the cables so that they will
not obstruct your playing; use
2.
Labels are affixed to the cable clips and cable ties
11
Make sure to wrap the cable ties
connection cable to indicate
around the pipes.
the pads to be connected. Make
connections as shown in the
illustration at right.
"CR2" is not used. It is used when
you are adding a cymbal using a
* Insert the plug firmly,
separately sold cymbal pad and
making sure it's all
cymbal mount (MDY-Standard). If
the way in.
you are not adding this, leave the cap
attached. Fasten it so that it does not
Label
obstruct your performance.
(CR1)
CY-5
(RD)
CY-5
(HH)
(T2) (T1)
CY-5
PDX-6A PDX-6A
TD-07
(SNR)
(T3)
PDX-8
PDX-6A
Hi-hat control pedal
9 When you've finished making connections, turn on the power as described
in the "TD-07 Owner's Manual," and verify that you can hear sound.
© 2021 Roland Corporation
8 AC adaptor 8 Drum key
8 Setup Guide (this document)
8 Owner's Manual set
7.
Attaching the cymbal mounts
7–1.
Insert the hi-hat and ride cymbal mounts
(short) and the crash cymbal mount
6
(long) into the holder of the curved pipe
7
, and adjust the position and direction
2
of all holders as shown in the illustration to
complete the setup.
Cymbal mount (Short) Cymbal mount (Short)
6 6
Cymbal mount (Long)
7
Ball
Pad mounts
The ball portion
9
should be visible by
the player
Pad mount
9
Pad mount
Kick pad
(with memory clamp)
10
Pedal plate
Assembly for a left-handed players
,
5
If you want to use a left-handed setup, assemble the
stand as follows.
5 Reattach the holders attached to the main unit
's pipes
1
so that there are two holders on the right and one on
the left.
5 Attach the kick pedal and the pedal plate to the left side
of the main unit .
1
5 Assemble the left and right arm sections so that straight
pipe "R" (short) is at the left and straight pipe "L" (long)
4
and the drum sound module holder are at the right,
3
and attach them to the main unit .
1
5 Attach the snare pipe
10 to the right side of the main
5
unit .
1
5 Attach the pad mounts
and cymbal mounts as
6 7
9 10
shown in the illustration.
Cymbal mount (Short) Cymbal mount (Short)
6 6
Cymbal mount (Long)
Drum
7
sound
module
Pad mounts
holder
Pad mount
9
9
Snare
pipe
Pad mount
Kick pad
5
(with the memory clamp)
10
Straight pipe R (Short) Pedal plate Straight pipe L (Long)
4 3
Cabling diagram for the connection cable
(As seen from the back)
CR1
RD HH
.
12
T2 T1
TD-07
T3
SNR
KIK
CR2
HHC
Headphones
Amplified speaker
etc.
to AC outlet
AC adaptor
Power cord
Cabling diagram for the connection cable
(As seen from the back)
CR1
HH RD
T2
T1
TD-07
T3
SNR
KIK
CR2
HHC
"CR2" is not used. It is used when you are adding a cymbal
using a separately sold cymbal pad and cymbal mount (MDY-
Standard). If you are not adding this, leave the cap attached.
Fasten it so that it does not obstruct your performance.