Black & Decker BHFEB520D Original Instructions Manual page 21

The charger will not charge a faulty battery pack, which may
be indicated by the light staying OFF or the red light rapidly
blinking. Take charger and battery pack to an authorized service
centre if light stays OFF or red light rapidly blinks.
nOTE: Refer to label near charging light on charger for
blink patterns.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and does
not indicate a problem. To facilitate the cooling of the
battery pack after use, avoid placing the charger or battery
pack in a warm environment such as in a metal shed or an
uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or
other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery pack
and charger to your local service centre.
3. You may charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Charging a Battery (Fig. C—E)
The supplied charger offers three possible ways to charge your battery.
- Cup charging
- Wall mounted cup charging
- Unit wall mounted charging
Standard cup charging
1. Plug the charger into an appropriate outlet before inserting
the battery pack 16 .
2. Insert the battery pack into the cup charger
3. The green LED will flash indicating that the battery is
being charged.
4. The completion of charge is indicated by the green LED
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Wall mounted cup charging
1. Mark the location of the charging station screw holes on
the wall (within reach of an electrical outlet for charging the
vacuum while it is on the charging station
2. Secure the charging station
appropriate screws and plugs for the type of wall, and
weight of the appliance.
3. Install the cup charger
(Fig. D). Ensure it is locked into place before proceeding.
nOTE: To remove the cup charger from the charging base
pull out on the retaining tabs
cup charger 19 out.
4. Plug the charger into an appropriate outlet before inserting
the battery pack.
5. Slide the battery pack 16
(Fig. C)
19 .
(Fig. D)
20 .
20 to the wall using
19 into the charging station
21 and lift the
onto the charging station
Wall mounted vacuum storage and battery
(Fig. E)
charging
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance. When mounting
to a wall, make sure the mounting method is suitable for the
wall type and is appropriate to the weight of the appliance.
1. Follow the instructions in the Wall mounted cup charging
section for instructions on mounting the charging
station 20
2. With the battery
charge port
slots 22 of the charging station.
3. The white LED on the vaccum will flash indicating that the
battery is being charged.
4. The white LEDs will illuminate in segments, displaying the
state of charge in the battery
5. The completion of charge is indicated by the white LEDs will
turn off. The pack is fully charged and may be used at this
time or left on the charger.
Wall mounted vacuum storage and battery
(Fig. E)
charging
The product can be attached to a wall to provide a convenient
storage and charging point for the appliance. When mounting
to a wall, make sure the mounting method is suitable for the
wall type and is appropriate to the weight of the appliance.
1. Mark the location of the charging station screw holes on the
wall (at a height that allows the unit to hang without hitting
the floor and within reach of an electrical outlet for charging
the vacuum while it is on the charging station
2. Fix the charging station
screws and plugs for the type of wall, and weight of
the appliance.
3. Install the cup charger
Ensure it is locked into place before proceeding.
nOTE: To remove the cup charger from the charging base pull
out on the retaining tabs
4. Plug the charger into an appropriate outlet.
5. With the battery
charge port
slots 22 of the charging station.
6. The white LED on the vaccum will flash indicating that the
battery is being charged.
7. The white LEDs will illuminate in segments, displaying the
state of charge in the battery
8. The completion of charge is indicated by the white LEDs will
turn off. The pack is fully charged and may be used at this
20 time or left on the charger.
Battery Type
The BHFEB520D operates on a 18 volt battery pack.
These battery packs may be used: BL1518, BL1518ST, BL2018,
BL2018ST, BL2518, BL4018, BL5018.
20 .
to a wall.
16 installed on the vacuum slide the
6 ,located on the vacuum base, onto the
20 to the wall using appropriate
19 into the charging station (Fig D.).
21 and lift the cup charger out.
16 installed on the vacuum slide the
6 ,located on the vacuum base, onto the
EnGLIsH
20 .
19