Bkpf-102Cb - Sony BKPF-101A Operation Manual

BKPF-102CB

General
Operating temperature
5°C to 40°C (41°F to 104°F)
Storage temperature
–20°C to +60°C (–4°F to 140°F)
Operating humidity 10% to 90% (no condensation)
Board: 195 × 310 mm (h/d)
Dimensions
3
(7 /
4
Connector panel: 195 × 25 mm
(h/w) (7
Mass Board: approx. 550 g (1 lb 3 oz)
Connector panel: approx. 180 g
(6.3 oz)
Power requirements +5 V DC: 1100 mA
−5 V DC: 600 mA
(supplied from the PFV-D20/
D50/D100A/D200A/D300)
Power consumption 8.5 W
Data transfer
Channel coding Scrambled NRZI
Transmission speed Input: 270 Mbits/s
Amplitude 0.8 Vp-p±10%
Cable length 200 m max.
(when using a Belden 8281
coaxial cable assuring signal
deterioration less than 25 dB/km
(f=10 MHz), except the active-
through output)
Digital input/output return loss
15 dB or more (5 MHz to 270
MHz)
Signal format Conforms to SMPTE 259M
4:2:2 component serial digital
video signal
Serial digital interface
Inputs/outputs
Serial digital input SDI IN connector (BNC type) (1)
0.8 Vp-p±10%, 75 ohms
4:2:2 component serial
digital video signal
Serial digital outputs Active-through output
connectors (BNC type) (4)
0.8 Vp-p±10%, 75 ohms
4:2:2 component serial
digital video signal
× 12
1
/ inches)
4
× 1 inches)
3
/
4
Analog outputs ANALOG OUT Y/G, B–Y/B,
R–Y/R connectors (BNC type)
(1 each)
Analog component video signals
or RGB signals (selectable with
a switch on the board)
RGB signals R: 0.7 Vp-p, 75 ohms
G: 0.7 Vp-p, 75 ohms
B: 0.7 Vp-p, 75 ohms
Defined with the color bar
signal 100/0/100/0.
YUV (CCIR) signals:
Y: 1.0 Vp-p (incl. Y sync 300 mV)
B–Y: 0.7 Vp-p
R–Y: 0.7 Vp-p
Defined with the color bar
signal 100/0/100/0.
YUV (Betacam 7.5% setup) signals:
Y: 1.0 Vp-p (incl. Y sync 286 mV)
B–Y: 0.7 Vp-p, 75 ohms
R–Y: 0.7 Vp-p, 75 ohms
Defined with the color bar
signal 100/7.5/77/7.5.
YUV (Betacam 0% setup) signals:
Y: 1.0 Vp-p (incl. Y sync 286 mV)
B–Y: 0.756 Vp-p, 75 ohms
R–Y: 0.756 Vp-p, 75 ohms
Defined with the color bar
signal 100/0/75/0.
Sync signal output SYNC connector (BNC type) (1)
2.0 Vp-p±10%, 75 ohms
Video characteristics
Sampling frequency Y: 13.5 MHz
R–Y, B–Y: 6.75 MHz
Digitization 10 bits
Band width Y: 5.75 MHz
R–Y, B–Y: 2.75 MHz
Y, R–Y, B–Y phase error
20 ns or less
K factor (2T pulse) 1% or less
Signal-to-noise ratio 60 dB or more
System delay approx. 3.9 µsec
EDH Conforms to SMPTE RP165
ISR output information
Error/warning messages: 1 item
Setup messages: 2 items
Design and specifications are subject to change
without notice.
9 (E)