1. Manuals
  2. Brands
  3. BlastPro Manuals
  4. Shot Blasting Machines
  5. BP-9-220
  6. Machine manual

BlastPro BP-9-220 Machine Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BP-9-220
MACHINE MANUAL
KEEP WITH MACHINE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BP-9-220 and is the answer not in the manual?

Questions and answers

Related Manuals for BlastPro BP-9-220

Summary of Contents for BlastPro BP-9-220

  • Page 1 BP-9-220 MACHINE MANUAL KEEP WITH MACHINE...

  • Page 2: Table Of Contents

    Table of Contents Applications ......................3 Specifications ......................3 Manufacturer ......................4 General ......................... 4 Work Site Assessment & Inspection ..............4 Start-Up Procedures ..................... 6 Operational Safety Procedures ................8 Shut-Down Procedures ..................8 Maintenance Procedures ..................9 Operating Instructions ..................10 Transportation .....................

  • Page 3: Applications

    The BP-9-220 has a 9” blast pattern and has the capability of 1/8” of depth removal in one pass. This portable, lightweight unit cleans and profiles in one easy step.

  • Page 4: Manufacturer

    An odorless, tasteless, & non-irritating gas, carbon monoxide can quickly become lethal. As a result, vapor propane must be used in all instances when the work area is enclosed or partially enclosed. The ® © 2011 Blastpro Manufacturing Inc.
  • Page 5 The work area must be checked for these materials before work can begin. Blastpro manufacturing, inc. does not warrant its equipment to be suitable for, or approved for, removing dangerous materials.

  • Page 6: Start-Up Procedures

    Wear grooves are acceptable until 50% of blade thickness has been worn away. When blade thickness has been worn away by more than 50%, replace all blades. • Check the front, side, & rear seal system & brush seals for excessive wear. ® © 2011 Blastpro Manufacturing Inc.
  • Page 7 It is consequently recommended that the operator make absolutely certain that the blast seals are in good working condition before putting the BP-9-220 into operation. • In the unlikely event of a failure, turn main power switch to the OFF position &...

  • Page 8: Operational Safety Procedures

    These particles should never be inhaled! • Empty all shot from the shot hopper on the shot blasting machine. Shot should never be left in shot blasting machine after work is performed. Never move or ® © 2011 Blastpro Manufacturing Inc.

  • Page 9: Maintenance Procedures

    • All other repairs must be completed by competent, qualified personnel. • Failure to replace loose or damaged parts could cause damage to the equipment and/or serious injury or death to the operator. • Verify that aggressive cleaning products are not used. ® © 2011 Blastpro Manufacturing Inc.

  • Page 10: Operating Instructions

    8. After confirming proper voltage with a voltmeter, insert the plug from the dust collector into a 110 volt electrical outlet. For the dust collector, use an outlet which is operated by a separate circuit breaker than is being used to power the shot blasting machine. ® © 2011 Blastpro Manufacturing Inc.
  • Page 11 “hot spot” to the left. If you visualize a clock, the opening of the control cage should be set at approximately 11:00 (leading edge) & 9:00 (trailing edge) on the clock. The size of steel shot used ® © 2011 Blastpro Manufacturing Inc.
  • Page 12 7. If this is only a temporary stoppage, then check the shot hopper & empty it if necessary. If this stoppage is the result of being done for the day, then empty the shot hopper no matter the amount of shot within it. ® © 2011 Blastpro Manufacturing Inc.

  • Page 13: Transportation

    • Filter cartridges must be kept in good, working condition. If the dust collector is not in proper, working order, then this can have a detrimental effect on the entire system. Improper ventilation can result in inadequate abrasive cleaning ® © 2011 Blastpro Manufacturing Inc.

  • Page 14: Inspection Timetable

    Wear Parts Kit BP-9-220V Spare parts starter kit S-26 DUST COLLECTOR Ermator S-26 Dust Collector Little Red Vac Hose 25’ vacuum hose Power Cord-01 Power cord (pricing ft.) Shot-02 Steel shot (35 lbs.) BT6917480 Blast wheel kit ® © 2011 Blastpro Manufacturing Inc.

  • Page 15: Blast Wheel Removal & Installation

    11. See the section in this manual about “Setting the Blast Pattern” before adjusting the control cage. Only blast wheels manufactured by Blastpro Manufacturing, Inc. should be used by the shot blasting machine. Other blast wheels that have not been tested by Blastpro Manufacturing, Inc.

  • Page 16: Fault Diagnostics

    Check bearing units, belts, sheaves, motor mounting, wheel housing, & any other associated parts to be sure that they are aligned & safely secured. ® © 2011 Blastpro Manufacturing Inc.
  • Page 17 Also, check fan rotation, The shot is contaminated. exhaust hose & connections, & air control gate to be sure that enough air flow is being delivered by the exhaust fan. ® © 2011 Blastpro Manufacturing Inc.
  • Page 18 & are is emitting concrete dust. clean. If necessary, replace filters in dust collector. Attach an end cap into open port. Also, check electrical Fan motor overload trips. system. ® © 2011 Blastpro Manufacturing Inc.

  • Page 19: Schematics

    BP-9-220 Machine Manual Schematics Item Description Part Number Mounting Plate/Grinder BT6962770 Felt Seal BTP002656 ® © 2011 Blastpro Manufacturing Inc.

  • Page 20: 5.1: Warranty Registration Information

    Blastpro Manufacturing, Inc., 6021 Melrose lane, Oklahoma City, OK 73127, within ten (10) days of acquiring Blastpro products in order to qualify for the one year limited warranty contained in the sales agreement. Blastpro provides as a limited warranty to original purchasers of Blastpro equipment, purchased within &...
  • Page 21 BP-9-220 Machine Manual damage caused by the use of any non-Blastpro parts or attachments on the equipment. To obtain repair or replacement under this limited warranty, the original purchaser must contact Blastpro at 1-877-495-6464. The original purchaser must be prepared to describe any alleged problem, as well as provide proof of purchase &...

  • Page 22: 5.1: Warranty Registration Card

    Cut Here Warranty Registration Card To ensure that your Blastpro machine is covered under warranty, please fill in the following information & mail it to BlastPro Manufacturing, Inc. 6021 Melrose Lane, Oklahoma City, OK 73127, or Fax to 405-495-1331. The following boxes must be...

Table of Contents