Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Reclaim v1
Summary of Contents for Reclaim v1
- Page 1 HEAT PUMP CONTROLLER V1.1 MANUAL INSTALLATION OPERATION MAINTENANCE...
- Page 2 This appliance may deliver water at high temperature. Refer to the Plumbing Code of Australia (PCA), local requirements and installation instructions to determine if additional delivery temperature control is required. Issue 01b | Jan 2023 Reclaim Energy | Owners/Installation Manual – Controller v1.1...
-
Page 3: Table Of Contents
Installing the Reclaim controller First time commissioning guide Front panel operation Modes of operation User access Status of operation LED and Button function summary Heat pump faults Communication/temperature sensor cable extension guide Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 4: Overview
This controller is designed to work only with the Reclaim CO2 domestic hot water heat pump. The key difference between V1 and V1.1 controller is the introduction of Option 6 which is a remote option control in V1.1. All functionalities between controllers are the same so for more information on how the controller works, please refer to the heat pump installation manual. -
Page 5: Before You Begin Installation
Remove ALL power sources before removing protective cover. The Reclaim Controller must be installed by a qualifi ed person. Ensure suitable over-current protection and RCD protection for the Reclaim Controller is in place. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 6: Installing The Reclaim Controller
Controller will run through start up checks including lighting all LEDs. Then fi rst display will be the time of day the controller thinks it is. Page 7 has details on how to adjust the time. Reclaim Energy | Owners/Installation Manual – Controller v1.1... - Page 7 RECLAIM CONTROLLER WITH THE COVER REMOVED Dry contact terminals for option 6 (page 9). Owners/Installation Manual – Controller v1.1 Owners/Installation Manual – Controller v1.1 | Reclaim Energy | Reclaim Energy RECLAIMENERGY.COM.AU...
- Page 8 2. The correct version of controller is chosen on the heat to be used. pump a. V1.1 controller requires “r1” to be set at “1”. This can be checked as follows on the PCB main of the heat pump Change the value of “r1” to “2” as follows: ii.
-
Page 9: First Time Commissioning Guide
CAUTION Make sure to complete the air purg before heating operation. It can cause unit failure Owners/Installation Manual – Controller v1.1 Owners/Installation Manual – Controller v1.1 Owners/Installation Manual – Controller v1.1 | Reclaim Energy | Reclaim Energy Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 10: Front Panel Operation
Menu Mode: Exit Menu Menu Mode: Next Setting Menu Mode: Enter Data Change Mode: Increment Data Change Mode: Decrement Data Change Mode: Accept setting Reclaim Energy | Reclaim Energy | Owners/Installation Manual – Controller v1.1 Owners/Installation Manual – Controller v1.1... -
Page 11: Modes Of Operation
18 hr cycle, the system contact switch and controller will automatically run to meet the legionella requirement 18 hours after the last time that 59°C has reached. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... - Page 12 The heat Pump output will be disabled. Purge mode is automatically turned off if the module The Purge output will be enabled. is currently displaying a heat pump error code. Purge mode will remain active for 5 minutes. Reclaim Energy | Owners/Installation Manual – Controller v1.1...
-
Page 13: User Access
In Data Change mode, when “Adj” is toggled on the display, the value can be changed by ising the UP button or the DOWN button Owners/Installation Manual – Controller v1.1 Owners/Installation Manual – Controller v1.1 | | Reclaim Energy RECLAIMENERGY.COM.AU... - Page 14 Wait 12 seconds for menu timeout. New time will appear. 12. When fi nished press MENU optn appears on display ENTER 13. Wait 12 seconds for menu timeout. New time will appear. Reclaim Energy | Owners/Installation Manual – Controller v1.1...
- Page 15 BOOST ENTER button (exit) to revert to the normal EXIT display or wait 30 seconds for auto 12. Press button to move to the User Hours- TEMP Run-1, “hru1” is displayed. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU...
-
Page 16: Status Of Operation Led And Button Function Summary
Green LED will fl ash. IMPORTANT Temperature control mode is disabled if a faulty temperature sensor is detected (Eg-8 and Eg-9), although the boost mode is still operational. Reclaim Energy | Owners/Installation Manual – Controller v1.1... -
Page 17: Heat Pump Faults
PCB board) or replaced before troubleshooting process per instructions given conducting more diagnosing. in the “Service Manual”. 2 Temperature control mode is disabled for Eg-8 and Eg-9 faults, however boost mode is still operational. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 18: Communication/Temperature Sensor Cable Extension Guide
Green White Brown White Brown Brown Brown Replace the lid, replace the four screws and tighten. Reconnect the Reclaim controller and turn on RJ45 PINOUT the power. CONFIGUARTIONS 10. Check that the sensor is reading correctly. Reclaim Energy | Owners/Installation Manual – Controller v1.1... - Page 19 1.200 0.3648 37.00 5.257 1.169 0.3572 35.38 5.081 1.138 0.3497 33.85 4.912 1.108 0.3424 32.39 4.750 1.080 0.3353 31.00 4.594 1.052 0.3284 29.69 4.444 1.025 0.3217 28.44 4.300 0.9990 0.3151 0.3087 Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU...
- Page 20 1300 383 815 HELLO@RECLAIMENERGY.COM.AU RECLAIMENERGY.COM.AU facebook.com/CO2HeatPump instagram.com/reclaimenergy...
Need help?
Do you have a question about the v1 and is the answer not in the manual?
Questions and answers