Advertisement
Advertisement
Related Manuals for Reclaim v1
Summary of Contents for Reclaim v1
- Page 1 HEAT PUMP CONTROLLER V1.1 MANUAL INSTALLATION OPERATION MAINTENANCE...
- Page 2 This appliance may deliver water at high temperature. Refer to the Plumbing Code of Australia (PCA), local requirements and installation instructions to determine if additional delivery temperature control is required. Issue 01 | Feb 2022 Reclaim Energy | Owners/Installation Manual – Controller v1.1...
-
Page 3: Table Of Contents
SECTION PAGE Overview Before you begin installation Installing the Reclaim controller Front panel operation Modes of operation User access Status of operation LED and Button function summary Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 4: Overview
This controller is designed to work only with the Reclaim CO2 domestic hot water heat pump. The key difference between V1 and V1.1 controller is the introduction of Option 6 which is a remote option control in V1.1. All functionalities between controllers are the same so for more information on how the controller works, please refer to the heat pump installation manual. -
Page 5: Before You Begin Installation
Remove ALL power sources before removing protective cover. The Reclaim Controller must be installed by a qualified person. Ensure suitable over-current protection and RCD protection for the Reclaim Controller is in place. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... -
Page 6: Installing The Reclaim Controller
Controller will run through start up checks including lighting all LEDs. Then first display will be the time of day the controller thinks it is. Page 7 has details on how to adjust the time. Reclaim Energy | Owners/Installation Manual – Controller v1.1... - Page 7 RECLAIM CONTROLLER WITH THE COVER REMOVED Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU...
-
Page 8: Front Panel Operation
Normal Mode: Sensor °C Normal Mode: Menu Mode Menu Mode: Exit Menu Menu Mode: Next Setting Menu Mode: Enter Data Change Mode: Increment Data Change Mode: Decrement Data Change Mode: Accept setting Reclaim Energy | Owners/Installation Manual – Controller v1.1... -
Page 9: Modes Of Operation
6 hours and the second can be set for 0 hours or more. Option6: Temperature control starting on contact closure on REMOTE input and remain enabled for duration of contact closure. Once contact is open, heating cycle will finish. Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... - Page 10 5 seconds. Eg-8 and Eg-9 faults, however boost mode is still operational. Purge mode is automatically turned off if the module is currently displaying a heat pump error code. Reclaim Energy | Owners/Installation Manual – Controller v1.1...
-
Page 11: User Access
XX-hr Setting – User 2 In Data Change mode, when “Adj” is toggled on the display, the value can be changed by ising the UP button or the DOWN button Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... - Page 12 EXIT Wait 12 seconds for menu timeout. New time will appear. MENU 12. When finished press optn appears on display ENTER 13. Wait 12 seconds for menu timeout. New time will appear. Reclaim Energy | Owners/Installation Manual – Controller v1.1...
-
Page 13: Status Of Operation Led And Button Function Summary
NORMAL MODE MENU MODE CHANGE MODE BOOST Boost On / Off Menu Exit Increment / Up EXIT TEMP Temprature Display Next Value Decrement / Down MENU Menu Mode Enter Accept ENTER Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU... - Page 14 THIS PAGE WAS INTENTIONALLY LEFT BLANK Reclaim Energy | Owners/Installation Manual – Controller v1.1...
- Page 15 THIS PAGE WAS INTENTIONALLY LEFT BLANK Owners/Installation Manual – Controller v1.1 | Reclaim Energy RECLAIMENERGY.COM.AU...
- Page 16 1300 383 815 HELLO@RECLAIMENERGY.COM.AU RECLAIMENERGY.COM.AU facebook.com/CO2HeatPump instagram.com/reclaimenergy...
Need help?
Do you have a question about the v1 and is the answer not in the manual?
Questions and answers