Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vmac A800185
Summary of Contents for Vmac A800185
- Page 1 Owner’s Manual A800185 VMAC Eliminator After-Cooler www.vmacair.com...
-
Page 2: Table Of Contents
Contents VMAC Document Revisions……………………………………………………………………………………………………………………..1 Equipment Specifications and Accessories ....................2 Safety ................................3 Installation ..............................5 Calibration/Testing ............................7 Operation ..............................9 Drawings and Components ......................... 10 Warranty ..............................11 VMAC Document Revisions Document # 1930225 Version Revision Details Revised by/date... -
Page 3: Equipment Specifications And Accessories
Equipment Specifications and Accessories Air Requirements: 80CFM-185CFM Electrical Requirements: 12V DC Connections: 1” NPT Intake & Discharge Accessories: Optional mounting bracket kit: A700143 After-Cooler and FRL/Water Sep rator Mounting Details... -
Page 4: Safety
VMAC will not be held responsible for any liability, injuries, loss or damage to individuals or to equipment as a result of the failure of any person to properly adhere to the procedures set out in this manual or standard safety practices. - Page 5 Safety Precautions Observe the following general safety rules: Pay attention to the system during operation; do not leave it unattended Follow safe work practices and wear appropriate safety equipment when operating air powered equipment, particularly eye and hearing protection ...
-
Page 6: Installation
1. Place the Eliminator After-Cooler in position and drill the appropriate mounting holes. 2. Fasten the rubber mount feet securely. If using VMAC optional mount kit A700143, install the After- Cooler unit to the brackets, then fasten the brackets securely. - Page 7 Over 8 feet 10 Gauge 10. Splice the white wire from the Eliminator After-Cooler to the white clutch wire at the VMAC VR compressor using 18 gauge wire. 11. If the Eliminator After-Cooler is not used in conjunction with a VMAC VR compressor, connect the white wire to a power source through an on/off switch using 18 gauge wire.
-
Page 8: Calibration/Testing
Calibration/Testing 1. If the truck is equipped with a VMAC VR system, place the manual transmission in neutral or the automatic transmission in park and fully apply the park brake. 2. Start and run the engine long enough to stabilize at base idle and reach normal operating temperature. - Page 9 FAN AIR FLOW DIRECTION AIR IN FROM COMPRESSOR AIR OUT WATER SEPARATOR / FRL UNIT AIR IN FROM COOLER AIR OUT TO AIR TOOLS...
-
Page 10: Operation
Operation If the Eliminator is correctly wired into the compressors on/off switch there will be no required manual input to activate or deactivate the Eliminator fan. If the Eliminator is installed on a separate compressor and using an auxiliary switch for activation, this switch should be turned on as soon as the compressor is turned on. -
Page 11: Drawings And Components
BOLT, HHCS, FL, PL, M8 X 1.25 X 20 1500631 SCREW, PHMS, M5 X 8 5000168 VALVE, MANUAL DRAIN 5830116 O-RING, VITON, ORB-16 3550891 HARNESS, FAN, A800185 3600124 COOLER, #16 ORB PORTS 3501070 FAN, 11" PUSHER 12V 1570163 WASHER, FLAT, 3/16 1550524 NUT, NYLOCK, 10-32 ITEM. -
Page 12: Warranty
DISCLAIMER AND WARRANTY SERVICE Any labor costs claimed in excess of VMAC’s set rate and/or times are not provided by this warranty. If applicable, any labor costs in excess of VMAC rate schedules caused by, but not limited to, location or inaccessibility of the equipment, travel time or labor provided by unauthorized service personnel are not provided by this warranty.
Need help?
Do you have a question about the A800185 and is the answer not in the manual?
Questions and answers