Ubiquiti UniFi UVC-Micro Quick Start Manual
  1. Manuals
  2. Brands
  3. Ubiquiti Manuals
  4. Camcorder
  5. UniFi UVC-Micro
  6. Quick start manual

Ubiquiti UniFi UVC-Micro Quick Start Manual

Hide thumbs Also See for UniFi UVC-Micro:
Table of Contents

Advertisement

Quick Links

Download this manual
®
Model: UVC-Micro
Q
S
G
uick
tart
uide

Advertisement

Table of Contents
loading

Related Manuals for Ubiquiti UniFi UVC-Micro

Summary of Contents for Ubiquiti UniFi UVC-Micro

  • Page 1 ® Model: UVC-Micro uick tart uide...

  • Page 2: Before You Begin

    Before You Begin The UVC Micro is designed to work with the UniFi® Video (v3.1.1 or higher) controller software. The software may be hosted on either: • The Ubiquiti Networks® UniFi NVR appliance (UVC‑NVR) • A Linux/Windows computer Note: The latest UniFi Video...

  • Page 3: Package Contents

    Package Contents UVC-Micro UVC-Micro Power Camera Base Adapter Flat Base Corner Base Mounting Plate Plate Tape Screws Screw Cable Clips (Qty. 5) Anchors (Qty. 6) (Qty. 5)

  • Page 4: Hardware Overview

    Hardware Overview Reset The LED will light steady blue during bootup. When the camera is ready to connect to the Wi-Fi network, the LED pattern will flash two times accompanied by two beep tones. Once connected to the network, the LED will glow a breathing pattern.

  • Page 5: Installation

    1. Hold the outer casing of the Power Adapter with the Ubiquiti U logo facing towards you, and push in the center of the logo until the adapter releases from the outer casing.
  • Page 6 2. Unwind the power cable to extend it to the desired length. Then lock the cable into the notch located under the bottom of the U logo. 3. Slide the outer casing back onto the adapter until it snaps into place.
  • Page 7 Mounting Options The camera may be used free-standing or mounted in several ways: • Magnetic Mounting • Mounting with Tape • Wall Mounting with Screws • Corner Mounting with Screws Magnetic Mounting 1. Attach the UVC‑Micro Camera and the power cable to the UVC‑Micro Base.
  • Page 8 2. Attach the camera assembly to a metal (steel) surface. *640-00157-02* 640-00157-02...
  • Page 9 Mounting with Tape 1. Remove the paper from one side of the Mounting Tape, and center the tape on the back of the Flat Base Plate. 2. Remove the paper from the other side of the Mounting Tape and attach the Flat Base Plate to the surface.
  • Page 10 Wall Mounting with Screws 1. Place the Flat Base Plate at the desired location and mark the two mounting holes. Note: If you are running the power cable inside the ceiling or wall, then mark the cable feed opening below the mounting holes.
  • Page 11 2. Use a 3 mm drill bit to drill a hole at each mark, and insert a Screw Anchor into each hole. 3. (Optional) When running the power cable inside the wall or ceiling, cut the hole for the power cable. Then feed the cable through the hole and the Flat Base Plate.
  • Page 12 4. Attach the Flat Base Plate to the surface by fastening a Screw to each Screw Anchor.
  • Page 13 Corner Mounting with Screws 1. Place the Corner Base Plate at the desired location and mark the two mounting holes. 2. Use a 3 mm drill bit to drill a hole at each mark, and insert a Screw Anchor into each hole.
  • Page 14 3. Feed the power cable through the back of the Corner Base Plate. 4. Secure the Corner Base Plate by fastening a Screw to each Screw Anchor.
  • Page 15 Attaching the Camera 1. Attach the power cable to the back of the UVC‑Micro Base. 2. Connect the UVC‑Micro Base to the Base Plate by inserting the mounting tabs into the slots on the base.
  • Page 16 3. Rotate the UVC‑Micro Base to lock it. 4. Attach the UVC‑Micro Camera to the UVC‑Micro Base, and pivot the camera to the desired angle.
  • Page 17 5. Plug the Power Adapter into a power outlet. To secure the connection, use the outlet cover plate screw to fasten the Power Adapter to the outlet. (Recommended) Note: (6) Cable Clips with adhesive tape are included to help hold the power cable in place.
  • Page 18 Set Up the UVC Micro Ensure you are running the latest version of UniFi Video, v3.1.1 or higher (UniFi NVR or computer‑based system). Download the UniFi Video User Guide for detailed information on how to set up and use UniFi Video: documentation.ubnt.com/unifivideo UniFi Video Mobile App For quick setup, a mobile app is available.

  • Page 19: Specifications

    Specifications UVC-Micro 40.7 x 40.7 x 40.8 mm Dimensions (1.61 x1.61 x 1.61") Weight 53 g (1.87 oz) Network Interface 2.4/5 GHz Dual-Band Wi-Fi Progressive Scan Sensor RGB CMOS 1/4" Lens EFL=2.38 mm / F2.4 View Angle 79.13° (H), 54.15° (V), 88.45° (D) Infrared LEDs with Night Mode Mechanical IR Cut Filter...

  • Page 20: Safety Notices

    Safety Notices Read, follow, and keep instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm.

Table of Contents