Page 1
Digital HD Video Camera Recorder HDR-CX450 HDR-CX455 HDR-CX485 SERVICE MANUAL 1st Edition...
Page 2
警告 このマニュアルは, サービス専用です。 お客様が, このマニュアルに記載された設置や保守, 点検, 修理などを行うと感電や火災, 人身事故につながることがあります。 危険をさけるため, サービストレーニングを受けた技術者のみご使用ください。 WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
Page 3
FÖRSIKTIGHET! 注意 指定以外の電池に交換すると, 破裂する危険があります。 Fara för explosion vid felaktigt placerat batteri. Byt endast mot samma eller likvärdig typ av batteri, 必ず指定の電池に交換してください。 enligt tillverkarens rekommendationer. 使用済みの電池は,国または地域の法令に従って När du kasserar batteriet ska du följa rådande lagar 処理してください。 för regionen eller landet. CAUTION PAS PÅ...
Page 4
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Manual Structure Purpose of this manual This manual describes the information items that premise the service based on the components parts assuming use of system and service engineers. Related manuals Besides this manual, the following manuals are available. • Operating Guide (Supplied with this unit) •...
Section 1 Trouble Shooting 1-1. Self-diagnosis Function 1-1-1. Self-diagnosis Function If an error occurs in this unit, the self-diagnosis function starts working and a code consisting of one alphabet and a four- digit number appears on the LCD. Classification of persons in charge, classification of faulty blocks, and details of errors can be checked by referring to this indication of five alphanumeric characters in the self-diagnosis code table.
Page 18
Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Abnormality of the wireless LAN The peripheral circuit of between CPU and wireless LAN module or CPU module may be faulty. Replace the board that contains this peripheral circuit. Difficult to adjust focus Turn power off and turn power on again.
Page 19
Self-diagnosis Code Symptom/State Correction Block Detailed Function Code Shift lens initializing failure Replacement of lens block. If an error occurs again, steadyshot circuit may be faulty. Replace the board that contains this peripheral circuit. Shift lens overheating (PITCH) Check signal line connections from CPU through steady- shot IC to PITCH/YAW drive.
1-2. Method of Coping with Shift Lens Error 1-2-1. E:62:02 Abnormality of IC for Steadyshot Identify the cause of the problem (lens or VC-1025 board), and replace the faulty lens or the VC-1025 board. 1-2-2. E:62:11 Shift Lens Overheating (Pitch) Start the Adjust Manual in the Adjust Station and execute the “Measure to E:62:11/12”...
Section 2 Service Note 2-1. Operation Notes 2-1-1. Flexible Board • Make sure that the conductive side of a flexible board does not have any stain or foreign materials. • Do not touch the conductive side of flexible boards with bare hands. •...
2-3. Precaution on Replacing the VC-1025 Board The board for repair is not recorded the information unique to a model. Therefore the following data are needed to write. Note The [LOAD AND WRITE] function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust Manual overwrites all data of the unit.
Applicable parts: • VC-1025 BOARD, COMPLETE (SERVICE) • WF-1004 BOARD, COMPLETE Note After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
2-4. Checking the Wi-Fi Function After this unit has been disassembled and reassembled, check the Wi-Fi function. Required equipment: Windows PC or smartphone with Wi-Fi interface Procedure: Turn on the power of the unit and enable the Wi-Fi function. (Upon completion of the preparation for Wi-Fi connection, the password for Wi-Fi connection is displayed.) Confirm on the PC or the smartphone that the unit is detected as a connectable wireless network.
Section 3 Adjustment For adjusting these models, the Adjust Station and the Adjust Manual are required. Adjust Station It is the software to start up Adjust Manual for each model. The installer of the Adjust Station and the installation manual are attached, be sure to confirm the contents of them. Adjust Manual It is the software to adjust and check digital cameras and camcorders for service.
Section 4 Replacement of Main Parts 4-1. Identifying Parts Control Switch Block (PS45300) LTOP Assy Built-In USB Cable CX455/CX485 IM Block • MM-102 Board JK Block • FP-2060 Flexible Board • JK-1009 Board • FP-2191 Flexible Board DC Jack Inner Cabinet Assy (449) •...
Page 42
View Position Top View Back View Left View Right View Front View Bottom View The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 HDR-CX450/HDR-CX455/HDR-CX485...
4-2. Disassembly 4-2-1. Overall Section-1 • Refer to “Overall Section-1” on exploded view for Ref. No. (Hooks) (Claw) (Claws) Overall Section-2 Disassembly Places The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 HDR-CX450/HDR-CX455/HDR-CX485...
Page 44
[1] Open the LCD {1} → #12 X 1 Right View [2] #2 X 1 → Close the LCD {2} → #2 X 1 Back View Bottom View [3] #12 X 2 → #2 X 2, #12 X 1 → Open the LCD {3} → #2 X 1 Left View Bottom View Right View...
4-2-2. Overall Section-2 • Refer to “Overall Section-2” on exploded view for Ref. No. (Hook) MIC901 (Claw) Lens Section (Note) (9 x 4 mm) Note Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 HDR-CX450/HDR-CX455/HDR-CX485...
Page 46
Disassembly Places The shape may be different from the illustration depending on models. 機種によって形状がイラストと異なる場合があります。 [2] #12 X 1 Left View [3] #12 X 1 → #2 X 1 Left View Top View HDR-CX450/HDR-CX455/HDR-CX485...
4-2-3. Lens Section • Refer to “Lens Section” on exploded view for Ref. No. CX455/CX485 #172 #172 #140 #172 (including CP001 (CMOS imager)) (Note ) #140 Cabinet (R) Section Note Be careful not to break the NFC Block Assy. NFC部組を折らないよう注意してください。 HDR-CX450/HDR-CX455/HDR-CX485...
Page 48
Disassembly Places [1] #140 X 1 Left View #140 [2] #12 X 1 → #2 X 1 Top View Right View [3] #140 X 2 Left View #140 [4] #172 X 2 Left View #172 HDR-CX450/HDR-CX455/HDR-CX485...
Page 49
Notes on Assembling the Lens Section How to distinguish the side of Optical Filter Block facing to Lens Device The one side of the Optical Filter Block has treated with IR cut coating. Mount the Optical Filter Block facing the IR cut coated side to the lens device.
4-2-4. Cabinet (R) Section • Refer to “Cabinet (R) Section” on exploded view for Ref. No. SP901 J901 LCD Section (Note 3) #288 #271 (Note 1) BT4200 (Note 2) BH4200 (Note 2) Note 1 This screw cannot be reused. Discard the screw removed once in servicing.
Page 51
Note 2 Replace the battery holder (BH4200) together when replacing the lithium storage battery (BT4200) on the JK-1009 board. (The battery holder removed once cannot be used again.) When mounting these parts, mount new battery holder first and attach new lithium storage battery next. JK-1009基板のリチウム蓄電池 (BT4200) を交換する場合は...
Page 52
4-2-5. LCD Section • Refer to “LCD Section” on exploded view for Ref. No. #288 (Note 1) (Note 2) (14 x 4.5 mm) (Note 3) LCD901 (Claws) Note 1 This screw cannot be reused. Discard the screw removed once in servicing. Instead, use a new screw.
Page 53
Note 2 Use this to cut or splice so that it becomes the designated size. 指定のサイズになるように形状を加工して使用してください。 Note 3 Install the magnet with the marking oriented as shown in the figure below. マグネッ トを取付ける際は, マ−キング面を図の位置にあわせ てください。 Marking マーキング 4-13 HDR-CX450/HDR-CX455/HDR-CX485...
Page 54
Notes on Assembling the LCD Section Attaching the FP-2192 Flexible Board 1. Fold dotted line parts of the FP-2192 flexible board as shown in the figure below. Valley fold Adhesive tape Adhesive tape Mountain fold Adhesive tape FP-2192 Flexible Board Adhesive tape Valley fold 4-14...
Page 55
2. Roll the FP-2192 Flexible Board 2 times in the Hinge Assy as shown in the figure below. FP-2192 Flexible Board Hinge Assy 2 Times 3. Install the Cover (M) Hinge/Cover (C) Hinge. Cover (M) Hinge Cover (C) Hinge 4. Attach the FP-2192 Flexible Board as shown in the figure below. FP-2192 Flexible Board 4-15...
Section 5 Repair Parts List 5-1. Note on Repair Parts (ENGLISH) NOTE: The components identified by mark or dotted line with • -XX, -X mean standardized parts, so they may have some mark are critical for safety. differences from the original one. Replace only with part number specified.
5-4. Accessories Except Japanese Model This Item is not supplied with the unit as an accessory, but it is prepared as a service part. When the customer requests printed one, ask Head Quarter. Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No.
Japanese Model 当商品はアクセサリーとして同梱されていませんが、 サービス部品として準備しております。 お客様から紙への印刷物を要求された場合は提供して下さい。 Ref. No. or Q'ty Part No. SP Description AC アダプター (AC-UUD12) 1-493-085-11 USB 接続サポートケーブル 1-838-714-31 1-846-028-21 HDMI ケーブル 4-585-631-01 * 取扱説明書 Ref. No. or Q'ty Part No. SP Description 8-022-175-00 リチャージャブルバッテリーパック NP- FV50/J Ref. No. or Q'ty Part No.