Table of Contents
Advertisement
Quick Links
PLANER THICKNESSER
OWNERS MANUAL
MODEL: PT10S & PT12S
Please Note:
This machine requires
a 16amp electric supply
with a Type C breaker
Charnwood Machinery, Cedar Court, Walker Road, Hilltop Industrial Estate,
Bardon Hill, Leicestershire, LE67 1TU
Tel. 01530 516 926
Fax. 01530 516 929
email: sales@charnwood.net
website: www.charnwood.net
1
Advertisement
Table of Contents
Related Manuals for Charnwood PT10S
Summary of Contents for Charnwood PT10S
- Page 1 MODEL: PT10S & PT12S Please Note: This machine requires a 16amp electric supply with a Type C breaker Charnwood Machinery, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. -
Page 3: Specification
Will be used up to the machines maximum limit with some long work periods. Expected maximum use of 1000 hours annually. Please Note: Using a product in excess of its rating will void the manufacturer’s free warranty. Specification PT10S PT12S Motor (induction) 2200w (3hp)/240v/50hz... - Page 4 Unpacking Open The Crate This product is packed into 1 wooden crate. To open the wooden crate: Cut the vertical straps Use a pry bar to release the nails around the base Lift off the complete lid. Remove Loose Items Remove the plastic cover, The fence, Carton of assembly parts.
- Page 5 Remove the side panel Use a cross head screwdriver to loosen 6 screws. 3 on each side of the panel. Lift and then remove the side cover. Unbolt From The Base The machine is fixed to the pallet base with 3 bolts. Use a 13mm spanner to undo the 3 securing nuts.
- Page 6 Identify The Loose Parts Side Fence Service Tools 5 Spare Cutters & Bolts Spring Plate Fence Bracket Cutter Guard 4 Fixing Bolts Support Arm Push Pad 4 Feet Assembly Remove the protective paper from the planing tables and clean the rust preventer from the table using WD40 or similar, and a soft cloth.
- Page 7 Fit the Fence Slide the dovetailed end of the fence into the support bracket. Push it all the way to the limit stop. Use the ratchet handle to lock the fence. Fit The Cutter Guard Support Arm Hold the arm up against the side of the machine.
- Page 8 Clean The Thicknessing Table To access the thicknessing table: Unlock the planing beds, one lock at each Raise the beds into the vertical position Swing the extractor hood over cutter block Remove the protective paper and clean the rust preventer from the table using WD40 or similar, and a soft cloth.
- Page 9 Using the Planer Thicknesser Feed Direction PLANING MODE Side Fence Cutter Guard Height Adjuster Outfeed Table Cutter Guard Lock Table Lift Lock On / Off Switch Infeed Table Infeed Table Lock Planing Depth Scale Planing Depth Adjuster Push Pad THICKNESSING MODE Lifting Handle Dust Hose Connection Planing Beds Release Catch...
-
Page 10: Switching Modes
PLANING MODE With the machine set up in planing mode: Use the Cutter Guard Height Adjuster to adjust the height of the Cutter Guard, so that the work piece can fit underneath. Set the Planing Depth Adjuster to the desired setting, reading off the Planing Depth Scale. If in doubt, set the depth to 0.5mm Connect a dust extractor to the 100mm diameter outlet. -
Page 11: General Guide
SWITCHING MODES To move from thicknessing mode to planing mode: Disengage the drive rollers by moving the Drive Rollers Lever into the lower position. Lower the thicknessing bed all the way down. Release the extractor hood from the retaining pin and swing the Dust Hood underneath the cutter block. -
Page 12: Cutter Replacement
Cutter Replacement Disconnect the machine from the supply The cutter block is fitted with 4 rows of Tungsten carbide cutters, 11 in each row. Each cutter has 4 sides and 4 cutting edges. A cutter can be rotated by 90 degrees to a new position to renew the cutting edge. -
Page 13: Troubleshooting
Troubleshooting Problem Cause Remedy Machine does not start Emergency stop activated Twist to release the red emergency stop button Faulty switch Replace switch Cutter Guard not fitted Check the alignment of the micro switch Only starts when Green Faulty switch Replace switch button is held down MCB trips on Start up... -
Page 14: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Planer & Thicknesser, Models PT10s and PT12S Conforms with the following EU Directives: Machinery Directive 2006/42/EC Electromagnetic Compatibility 2014/30/EU Conforms with the following UK Regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016 And further conforms to the machinery example for which the EC type examination Certificate No. - Page 15 Charnwood PT10S & PT12S Parts Diagrams Drawing A:...
- Page 16 Drawing B:...
- Page 17 Drawing C:...
- Page 18 Charnwood PT10S & PT12S Parts List Part No. Description Part No. Description Base Stand Cover Plate Flat Washer M5 Screw M5 x 8 Foot Nut M10 Right Inner Plate Countersunk Screw M5 x 6 Screw M5 x 50 Nut M5...
- Page 19 Lead Screw Elastic Pin Nut M10 Flat Washer Gear Box Elastic pin Nut M8 Nut M6 Block Hex Socket Head Screw M6 x 25 Digital Readout Hex End Set Screw M5 x 8 Right Support Bracket Flat Washer Spring Washer Screw M8 x 25 Retaining Ring Eccentric Rod...
- Page 20 Spring Washer Flat Washer Left Support Plate Left Support Base Outfeed Table Left Axle Left Table Bracket Eccentric Sleeve Screw M8 x 30 Cylindrical Pin 6 x 20 Protective Cover Screw M6 x 10 Flat Washer 6 Hex Socket Screw M8 x 12 Hex Socket Screw M8 x 20 Screw M8 x 30 Spring Washer...
- Page 21 Nut M6 Nut M6 Feet Screw M6 x 16 Extractor Outlet 100mm Diameter Bolt M6 x 10 Nut M6 Plate Countersunk Head Screw M6 x 12 Pressure Plate Foot Elastic Cylindrical Pin 3 x 10 Connection Plate Right Metal Plate Guide Plate Left Metal Plate Square Bolt 10 x 30...
-
Page 22: Wiring Diagram
Button (Red) Upper Cover Switch Board Tapping Screw ST4 x 16 Switch Label Tapping Screw ST4 x 10 Switch Nut M4 Countersunk Head Screw M4 x 35 Bolt M5 x 25 Strain Relief Spring Split Ring Ejector Electrical Box Screw M5 x 16 AC Contactor Strain Relief Strain Relief... - Page 24 Last Updated January 2023 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...