Televes DATBOSSMIX LR Quick Start Manual

Televes DATBOSSMIX LR Quick Start Manual

Advertisement

Antenna Kit / Kit Antena
Ref. 148383
(Ant-148331 + PSU-550104)
UHF Directors
UHF Director Spacers
E
F
UHF Refl ectors
G
x2
Low-VHF dipole/refl ectors
Dipole Assembly
Fastening hardware
AA
AB
AC
x2
x2
x4
(b1)
B1
(b2)
B2
(b3)
B3
Mounting Clamp
Assemblies
Low-VHF dipole
H
x2
Assemblies
J
x2
I
x2
K
x3
N
x2
S
x4
T
AD
AE
AF
AG
x2
x2
x2
Main Assembly
(a1)
(a2)
(a3)
Low-VHF Refl ector Extension
(c4)
Support Braces
Refl ector Self-locking Clamps
O
x2
L
x2
M
x4
VHF Refl ectors
R
x2
Connector
U
V
Included 10mm wrench
Z
BB
x2
AH
BA
x3
x8
x8
MIX LR
A
C
D
x2
P
x2
Q
x4
PSU
Additional spare parts
(x1)
BC
x2
(a4)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DATBOSSMIX LR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Televes DATBOSSMIX LR

  • Page 1 MIX LR Antenna Kit / Kit Antena Ref. 148383 (Ant-148331 + PSU-550104) UHF Directors Main Assembly (b1) (a1) (b2) (a2) (a4) (b3) (a3) Low-VHF Refl ector Extension (c4) UHF Director Spacers Mounting Clamp Assemblies Low-VHF dipole Support Braces Assemblies Refl ector Self-locking Clamps UHF Refl ectors VHF Refl ectors Low-VHF dipole/refl ectors...
  • Page 2 Antenna assembly / Montaje de la antena NEEDED TOOLS Scan to watch PH #2 assembly video Included 10mm wrench Screw driver Cutter Cable stripper Note: Start the assembly procedure after thoroughly checking all parts and becoming familiar with them.  ...
  • Page 3 Place the plastic spacers on the support braces , closer to the curved part of the support brace as indicated. Slide the mounting clamp assemblies on the support braces starting from the support brace end that is not curved and tighten the bolts loosely once in place over the plastic spacers , as they will be fully tightened later.
  • Page 4 Attach metal plates to the dipole as shown in the picture with the use of the bolts and the nuts Insert the dipole assembly into the antenna orange junction box, sliding it through the guide slot to the point where you will hear an audible “click”...
  • Page 5 Join both sections of the main antenna boom by inserting the end (c4) of the Low-VHF assembly into the end (a4) of the main assembly To ensure a strong joint, place pieces on both sides of the holes of the end (a4) and fasten them with the use of the bolt and the nut Using the hole in supports...
  • Page 6 Release the shackles from the mast clamps Elevation screws removing and saving the shackle and nuts. Place the antenna assembly on the mast (not included) and proceed to replace the shackles and tighten the nuts to attach the assembly to the mast. The “elevation screws”...
  • Page 7 Seen in step ..4, 15 9-14 8, 16 Safety Instructions: Technical specifi cations / Características técnicas * The gain is automatically LIGHTNING PROTECTION BOSS ON (Active) adjusted according to the level If installed outdoors, be sure the antenna system is grounded so Low VHF High VHF as to provide protection against voltage surges and built-up static...
  • Page 8 Televes USA LLC. Norfolk Tech Center 16596 E. 2nd Avenue Aurora, CO 80011 televes.usa@televes.com www.televes.com 2022 © Copyright, Televés S.A.U.

This manual is also suitable for:

148383

Table of Contents